VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Golf 1 GTD Timing Belt Crankshaft Timing Mark

 
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
Willi_dekathis



Joined: 01/12/2017
Posts: 16
Karma: +1 / -0   Thank you, like it!


Free account, no CAN development support

Post01-05-2018, 9:17    Subject: Golf 1 GTD Timing Belt Crankshaft Timing Mark Quote

Hey everyone.

Having completely overhauled my GTD after the issues with the H-approval, the car sat idle for about a year. I recently got it running again and warmed it up. What I've noticed is that it seems to be bouncing up and down quite a bit when the engine is running. The vibration gets stronger when you accelerate.

Then it occurred to me that the intermediate shaft might be the culprit. I looked into whether there's an OT marking on it. I also checked an old pulley that I still have in the rack, but there's no marking on that either.

My question to you is: Is there a specific position that the intermediate shaft needs to be in, or perhaps a timing mark or something similar?
Here's the translation:

"What I can imagine is that the counterweight on the intermediate shaft is currently amplifying the imbalance. Or am I approaching this from the wrong angle, and does it not matter how the shaft is positioned?"

I hope it's clear what I mean, and that you can help me.

Best regards,

Willi.


Translated on 31-10-2026, 17:48.
Back to top Profile PM
Steffen G
Profi-Schrauber
Profi-Schrauber


Joined: 10/26/2006
Posts: 2557
Karma: +591 / -0   Thank you, like it!
Location: bei Zwickau

Premium Support

Post01-05-2018, 11:05    Subject: Golf 1 GTD Timing Belt Crankshaft Timing Mark Quote

Hello! The timing belt runs on the back side, against the intermediate shaft pulley. There's nothing you can adjust there.
Grüße, Steffen!

Golf 4 TDI,
T4 Doka-Pritsche, paar Oldtimer


Translated on 31-10-2026, 17:50.
Back to top Profile PM
Herbert
Profi-Schrauber
Profi-Schrauber


Joined: 06/22/2005
Posts: 4636
Karma: +1350 / -0   Thank you, like it!


Premium Support

Post01-05-2018, 17:21    Subject: Golf 1 GTD Timing Belt Crankshaft Timing Mark Quote

Hi,
The intermediate shaft also does not have a balancing weight; its sole purpose is to drive the oil pump and vacuum pump.
Is the engine just vibrating, or is it also experiencing fluctuations in RPM?
When dealing with vibrations, the suspicion usually points towards issues with the compression or the fuel injectors.
hg
Herbert.
Horch A4 8K CJCD
Golf 7 DDYA
(+ Audi 80 Avant B4 1Z 475Tkm - habe ich vom ersten bis zum letzten Tag gerne gefahren)
(+ Passat Variant 32B CY 400Tkm)


Translated on 31-10-2026, 17:51.
Back to top Profile PM
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Similar articles and topics
Topic Forum
No new posts Golf 4 Fault Code Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Golf IV 1.9 TDI AXR - Stutters under load Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Golf 5 1.4 BUD Misfire 2. Cylinder Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Golf MKB BSE timing belt or timing marks Gasoline Engine Technology
No new posts Crankshaft Position Sensor AFN Automatic VW Golf 3 Diesel Engine Technology
No new posts Faulty bearing, Alhambra intermediate bearing has play. Diesel Engine Technology
No new posts OT Marking for AFN? Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.