VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Engine Stalling: Causes and Solutions

 
Go to page: 1, 2  Next
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
Hoin
Blaumann
Blaumann


Joined: 04/25/2002
Posts: 35
Karma: +6 / -0   Thank you, like it!
Location: Langenkamp

Premium Support

Post24-07-2003, 21:52    Subject: Engine Stalling: Causes and Solutions Quote

I installed a TDI PD -ATD- engine in my T3 van.
At that time, the engine had 3800 kilometers on it; currently, it has around 22000 kilometers.
Last winter, the engine stalled while I was exiting the highway after a long drive, with the temperature at -6 degrees Celsius. After that, it would repeatedly stall at every intersection where I had to stop.
I then managed to get the remaining 50 kilometers home.
During the drive, I also noticed a loss of power.
Every time I tried to start the engine, I had to hold the accelerator pedal down for a very long time, about a minute, before the engine would finally start. I got the impression that the entire fuel line was empty and that air had to be bled out first.
I changed the diesel filter at home (I cut it open but didn't find any contamination), but even with the new filter, the problem happened again shortly after.
Also, also, minus 5 degrees Celsius.
In the last six months, everything went back to normal.
This problem has been recurring for some time now.
I've noticed that these misfires tend to occur after longer drives.
After driving approximately 500 km (with no issues on the highway), I exited the highway, and at a traffic light, my engine stalled.
After playing the organ for a while, it starts up again.
On the next trip with a full tank, the same thing happened again after about 100 km.
Currently, I'm driving without any problems, but I haven't taken any long trips recently. As I mentioned, I've had two full tanks of gas without any issues so far.
In the last two weeks, an additional issue has emerged: a loss of power between 2000 and 3000 engine revolutions per minute.
Short question: What could be the reason?
Best regards, Hoin.
Düsen nicht dümpeln!!!


Translated on 27-10-2026, 3:50.
Back to top Profile PM Email
Leigh
Guest




 


Free account, no CAN development support

Post24-07-2003, 23:22    Subject: Engine Stalling: Causes and Solutions Quote

Regarding the starting problem, please check the relay that supplies voltage to the engine control unit.
Hairline cracks often occur at the solder joints.

Just solder it, and you're done!


Translated on 27-10-2026, 3:53.
Back to top
Rudi
Guest




 


Free account, no CAN development support

Post25-07-2003, 6:30    Subject: Engine Stalling: Causes and Solutions Quote

Hi,
The fuel tank ventilation is okay icon_question.gif.

Best regards, Rudi.


Translated on 27-10-2026, 3:53.
Back to top
Markus H.
Guest




 


Free account, no CAN development support

Post25-07-2003, 13:28    Subject: Engine Stalling: Causes and Solutions Quote

Hi,

Oil pressure OK?
The same thing happened with our old 200 D after a long trip (which was always long because it was so slow icon_lol.gif).
Before that, the oil pressure would always drop when leaving the autobahn.

Is there a connection between low oil pressure and the engine stalling? I'm not entirely sure.


Translated on 27-10-2026, 3:54.
Back to top
Hoin
Blaumann
Blaumann


Joined: 04/25/2002
Posts: 35
Karma: +6 / -0   Thank you, like it!
Location: Langenkamp

Premium Support

Post25-07-2003, 20:12    Subject: Engine Stalling: Causes and Solutions Quote

Hello Rudi,
I have never detected any vacuum in the fuel tank.
I can't say anything about the oil pressure.
Thank you very much, nonetheless.
Düsen nicht dümpeln!!!


Translated on 27-10-2026, 3:54.
Back to top Profile PM Email
Japanese
Guest




 


Free account, no CAN development support

Post29-07-2003, 0:00    Subject: Engine Stalling: Causes and Solutions Quote

The oil pressure has nothing to do with it. It only indicates whether the oil supply for lubrication is sufficient.


Translated on 27-10-2026, 3:55.
Back to top
dieselschrauber
Administrator
Administrator
Avatar-dieselschrauber

Joined: 04/12/2002
Posts: 18135
Karma: +804 / -0   Thank you, like it!
Location: St.Gallen
2018 Volkswagen T6 Consumption


Post29-07-2003, 7:56    Subject: Engine Stalling: Causes and Solutions Quote

Hello Hoin,

What about the power supply for the EDC?
Error codes read?

Best regards, Rainer.


Translated on 27-10-2026, 3:55.
Back to top Profile PM WWW Garage
Hoin
Blaumann
Blaumann


Joined: 04/25/2002
Posts: 35
Karma: +6 / -0   Thank you, like it!
Location: Langenkamp

Premium Support

Post31-07-2003, 20:09    Subject: Engine Stalling: Causes and Solutions Quote

Hello Rainer,
Currently, my engine is running, and it's lacking some power, as described in the previous text, but it's not currently shutting off.
"I don't understand what you mean by 'power supply for EDC'."
Error memory is empty.
Thank you to everyone who is working hard for me.
Best regards, Hoin.
Düsen nicht dümpeln!!!


Translated on 27-10-2026, 3:56.
Back to top Profile PM Email
dieselschrauber
Administrator
Administrator
Avatar-dieselschrauber

Joined: 04/12/2002
Posts: 18135
Karma: +804 / -0   Thank you, like it!
Location: St.Gallen
2018 Volkswagen T6 Consumption


Post01-08-2003, 9:36    Subject: Engine Stalling: Causes and Solutions Quote

Hello Hoin,

There used to be faulty power supply relays for the EDC in engines with VE injection systems.
If the engine control unit for the fuel injection system loses power, the engine will simply shut off.
I don't know how the EDC's power supply is connected to your engine.
Nevertheless, you should check that.

Best regards, Rainer.


Translated on 27-10-2026, 3:57.
Back to top Profile PM WWW Garage
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post01-08-2003, 10:11    Subject: Engine Stalling: Causes and Solutions Quote

Hi,

I have a few questions/ideas.

- An ATD engine is a PD engine with a very sensitive fuel supply and return system. It's important that the return cooling functions properly, otherwise your engine will eventually receive extremely hot diesel fuel, which will cause it to run poorly and may even stall. What have you done regarding fuel cooling?
- Furthermore, I believe I recall that the inclination angle at which the engine is mounted in the T3 is significantly greater than that of the donor vehicle. This raises the possibility that the tandem pump may no longer function correctly, and that the mixing of (cold) incoming fuel with warm return fuel may become unbalanced, or that it may even introduce air (bubbles). Can you rule this out?
- PD (Positive Displacement) motors require a pre-charge pump because the suction pressure of the vacuum pump is not sufficient to supply the PD elements with enough fuel in terms of both quantity and pressure. Do you have a pre-charge pump installed in your system?

Perhaps this will be helpful for now. I might have more to add later.
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 27-10-2026, 3:59.
Back to top Profile PM
Michael II
Profi-Schrauber
Profi-Schrauber


Joined: 04/12/2002
Posts: 1132
Karma: +3 / -0   Thank you, like it!
Location: Stuttgart

Support

Post01-08-2003, 10:34    Subject: Engine Stalling: Causes and Solutions Quote

Hello,

Have you checked that?

Affected engine number ranges.
ATD 044 481 to ATD 049 016.

There is a possibility that this is due to a burr on the contact surface.
...the toothed wheel of the timing belt can be used to attach and detach the screw connection.
Tschüss

Michael II


Translated on 27-10-2026, 4:00.
Back to top Profile PM
Hoin
Blaumann
Blaumann


Joined: 04/25/2002
Posts: 35
Karma: +6 / -0   Thank you, like it!
Location: Langenkamp

Premium Support

Post02-08-2003, 22:10    Subject: Mootr Shut Down: What Happened? Quote

Hello Rainer,
I will check that with the EDC.
Hello Bertil,
It is correct that the motor is installed at an angle (tandem pump).
The original pre-lift pump from the donor vehicle is installed in the tank.
The original diesel cooler is also located in the return line, underneath the vehicle.
Regarding the air bubbles:
Here, I suspect the cause of my problem, because I usually only experience this prolonged idling after running the fuel tank dry or replacing the diesel filter. I can't understand why it happens at completely irregular intervals. I'm driving, the engine is running, and at every intersection, at every traffic light, the engine cuts out as I'm slowing down. I also noticed that the engine had a loss of power, similar to what you'd experience with a clogged diesel filter, but as mentioned above, the replaced filter was clean, and while the problem was somewhat better with the new filter, it wasn't completely gone. This all happened during the winter. Then I had no problems for several months (I also didn't drive very long distances, maybe 200 km at a time), but suddenly the problem reappeared after a trip of over 500 km, during which I took breaks.
Unfortunately, I haven't been able to check the air bubbles yet because the engine always failed while I was on the road.
I'm going to install a transparent hose.
I would actually rule out the issue of the increased temperature coming from the return line.
because it also happened to me after a relatively short distance, even in sub-zero temperatures.
I must also add that, in my opinion, the current reduced performance is not related to the engine failing.
OK Michael,
I can look into the engine number for you and I'll pass the number along to you.
I'm still having a problem with the engine number. I have the engine number, but I can't access the vehicle identification number (VIN) of the donor vehicle (which was a Golf IV).
I need a second key. VAG (Volkswagen Group) says they require the vehicle's VIN (Vehicle Identification Number) to provide a key.
Short additional question: Can I find the vehicle identification number (VIN) using the engine number?
VW representatives are citing data privacy concerns.
Another thank you to you all.
Hi.
Düsen nicht dümpeln!!!


Translated on 27-10-2026, 4:04.
Back to top Profile PM Email
ErJoKri
Blaumann
Blaumann


Joined: 05/22/2002
Posts: 27
Karma: +6 / -0   Thank you, like it!
Location: Nähe Köln

Free account, no CAN development support

Post03-08-2003, 6:57    Subject: Engine Stalling: Causes and Solutions Quote

Hello Hoin,

"I recently experienced intermittent engine cutouts with my AFN engine. The EDC relay, which receives a signal from the MSG (Main System Module), was not engaging. In my case, it was a cold solder joint on the MSG. This typically occurred either in the morning when it was cold or during longer drives, causing brief engine cutouts (less than 1 second). Eventually, it even led to a complete engine failure on the highway."
However, it could be a completely different issue in your case. Therefore, here are a few questions:

"If you turn the ignition key to position 2 ("glow plug"), does the glow plug indicator light up for about 2 seconds even at normal temperature (as a self-test of the engine control unit)?"
If so, does the relay for the EDC also engage (located in my AFN's electrical box next to the MSG)?
You can test the glow plug relay shortly after an engine failure by disconnecting the coolant temperature sensor and then turning on the ignition. The control unit will then release the signal for preheating for approximately 20 seconds. The easiest way to measure this is with a multimeter connected to a disconnected glow plug connector.

"2. If you have to crank the engine for a long time to get it started, it sounds like there's no combustion happening at all – not even occasionally in one cylinder, so more like a monotonous, relatively fast turning of the warm engine? Or does it occasionally shake? The latter, in my opinion, suggests a fuel supply problem. The former is more likely to indicate an electrical issue."

Best regards,
seriously


Translated on 27-10-2026, 4:08.
Back to top Profile PM
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post03-08-2003, 7:52    Subject: Engine Stalling: Causes and Solutions Quote

ErJoKri wrote:
Recently, I also experienced intermittent engine cut-outs with the AFN engine. In my case, the relay for the EDC, which receives a signal from the MSG, was not engaging. It turned out to be a cold solder joint in the MSG. This typically occurred either in the morning when it was cold or during a longer drive, and it caused brief engine cut-outs (less than 1 second). Eventually, it even resulted in a complete engine failure on the highway.

hi

A cold solder joint in the engine control unit? Was that related to the botched chip tuning?

If not: Could you describe the location of the component in the engine control unit (e.g., for the error database) so that fellow sufferers can get a rough idea when encountering similar issues?
Gruß Ulf
_________

MG4 Electric


Translated on 27-10-2026, 4:11.
Back to top Profile PM Garage
Hoin
Blaumann
Blaumann


Joined: 04/25/2002
Posts: 35
Karma: +6 / -0   Thank you, like it!
Location: Langenkamp

Premium Support

Post03-08-2003, 19:13    Subject: Engine Stalling: Causes and Solutions Quote

First, let's talk about Michael.
The engine number is 021483. I believe this engine does not fall under the problem you described.
EJOKRI:
Regarding your explanation, I can say that the glow plug system is activated with every start, at least the glow plug indicator light illuminates on the dashboard.
I can't say for sure whether the relay is engaging. I installed the relay in a rather hidden location after the modification. Also, I'm experiencing warm-start problems, but that's been an issue from the beginning.
I am currently in the process of simulating a cold start for the engine every time it starts, using a relay and an external temperature sensor. I am currently in the theoretical phase.
Regarding the organs:
After approximately 40-50 seconds of cranking, the engine starts to spin up faster, and then the first cylinders begin to fire, until it finally starts after another 5-6 seconds.
Keep it up.
Best regards, Hoin.
Düsen nicht dümpeln!!!


Translated on 27-10-2026, 4:13.
Back to top Profile PM Email
ErJoKri
Blaumann
Blaumann


Joined: 05/22/2002
Posts: 27
Karma: +6 / -0   Thank you, like it!
Location: Nähe Köln

Free account, no CAN development support

Post04-08-2003, 15:10    Subject: Engine Stalling: Causes and Solutions Quote

@ Ulf:

Okay, that was the sloppy solder joint on the EEPROM socket. This apparently caused the Msg system not to perform a proper system check when the ignition was turned on (the glowing filament indicator in the speedometer did not light up (!) for about 2 seconds). Additionally, the relay for the fuel injection pump was not activated --> no diesel --> engine off, even while driving icon_sad.gif.

@ Hoin:

The issue with air in the fuel system sounds plausible. This weekend, I helped get a gasoline-powered engine running. It had a leaky fuel line on both the supply and return lines to the carburetor --> after a longer period of inactivity, all the gasoline flowed back into the tank, and the fuel pump ran dry --> even prolonged cranking didn't help, because the pump kept sucking in air.
Could the issue you're experiencing be related to the fact that, depending on the fuel temperature, either more fuel is pumped from the tank towards the injector, or more fuel is returned from the injector? If either of those lines were drawing in air, you would experience different failure rates depending on the fuel temperature.

Best regards,
Ernst.


Translated on 27-10-2026, 4:16.
Back to top Profile PM
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Go to page: 1, 2  Next
Similar articles and topics
Topic Forum
No new posts Ford with TDCi engine: rough running, stalling General Tips
No new posts Doku Caddy 9K9: Engine Stalling, Error Code 1268 Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Document: Engine starts, then immediately stalls. Model: ... Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Engine won't start, stalls at traffic lights Diesel Engine Technology
No new posts TDI Engine with Gas Transmission: Possible? Diesel Engine Technology
No new posts A4 1.9 TDI Engine Failure: Causes & Fixes Diesel Engine Technology
No new posts Engine Stalls When Clutch Is Pressed On-Board Diagnostics (OBD)
Jump to:  
You cannot post new topics in this forum.