VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

VAGCOM Adapter 2.0: Problems and Issues

 
Go to page: 1, 2  Next
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post05-10-2002, 19:45    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hello everyone.

During my first attempt to connect to my tractor using a laptop and VAGCOM, I encountered previously unknown error messages, even though the adapter test was positive.

Cannot synchronize baud rate (for the motor) or...

Too many communication errors to continue (with the ABS).


After some troubleshooting, I found that the relatively high, energy-efficient resistance values for resistors R8 and R9 were making the output transistor T1 somewhat "slow."

Replacing the components with the values specified by Noxon and Stautz (1 kOhm each) fixed the error.
Sorry to everyone who is experiencing the same problems with the 2.0 replica...


By the way, I couldn't establish a connection with version 1.1 (without the output transistor, which works perfectly on my PC) either, using a laptop: the adapter wasn't recognized.
Apparently, the PC's COM port can provide more power to the adapter. The LEDs also appear to be slightly brighter in that case.


@Rainer: I'm sending you the circuit diagrams again with the modified resistor values.
Just to be on the safe side, I'm also using 1.8 kOhms for R3, because some forum members have already experienced problems with 2.7 kOhms.

Sincerely,

Ulf.


Translated on 20-10-2026, 12:47.
Back to top Profile PM Garage
dieselschrauber
Administrator
Administrator
Avatar-dieselschrauber

Joined: 04/12/2002
Posts: 18135
Karma: +804 / -0   Thank you, like it!
Location: St.Gallen
2018 Volkswagen T6 Consumption


Post05-10-2002, 21:15    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hello Ulf,

Don't give up just yet! Upload it then.

Best regards, Rainer.


Translated on 20-10-2026, 12:49.
Back to top Profile PM WWW Garage
Gremlin
Guest




 


Free account, no CAN development support

Post05-10-2002, 23:21    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Don't despair...

I'm going to try putting something together next week.

CU Gremlin.


Translated on 20-10-2026, 12:49.
Back to top
OlliP
Guest




 


Free account, no CAN development support

Post06-10-2002, 9:17    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hi,

without having a good understanding of the background - and
I have absolutely no experience with those parts.
Just a quick mention of the electronics magazine 'Elektor'!
In the last issue, there was a set of instructions for building an OBD-2...
Cable included. This allows for VAG Com and more - meaning multiple functionalities.
Vehicle logs - not just for VAG!
It should include Opel, Ford, BMW, DC (presumably referring to a brand or type), many Japanese cars, and more.
it's something to address.

I haven't tried it myself - I only know about it from reading about it elsewhere.
Forums and newsgroups!

@Ulf: Maybe you should check out what THEY are doing differently!

Good luck.
Olli.


Translated on 20-10-2026, 12:51.
Back to top
Gremlin
Guest




 


Free account, no CAN development support

Post06-10-2002, 13:42    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

I'll definitely take a look.

I already laughed my head off about ELV building regulations 10 years ago. If they're still stuck in that cheapskate mindset...

CU Gremlin.


Translated on 20-10-2026, 12:52.
Back to top
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post06-10-2002, 18:00    Subject: Electronics Projects: DIY & Tutorials Quote

OlliP wrote:
without having a good background - and
I have absolutely no experience with those parts.
Just a quick mention of the electronics magazine "Elektor"!
In the last issue, there was a set of instructions for building an OBD-2...
Cable installed.
Bitte gib mir den deutschen Text, den du übersetzt haben möchtest.
@Ulf: Maybe you should check out what THEY are doing differently!


Hi Olli,

I'll definitely do that... if the product is still available.

What number is that?
Gruß Ulf
_________

MG4 Electric


Translated on 20-10-2026, 12:53.
Back to top Profile PM Garage
Georg_G
Profi-Schrauber
Profi-Schrauber


Joined: 04/12/2002
Posts: 332
Karma: +6 / -0   Thank you, like it!
Location: Freiburg im Breisgau
2012 Volkswagen Golf
Support

Post06-10-2002, 18:11    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hello Ulf,

The versions 1.1 and 2.0 that you suggested didn't show the breakthrough success with me either.
But I already wrote in the other thread about the changes that were necessary to get my old, underpowered mini-notebook running.

I only applied the following changes that you suggested to your original version.
Quote:


For those who want to try it out in advance:

1. Insert an additional diode (cathode connected to R1) between pin 7 of the PC connector and resistor R1.

Insert an additional diode between OK 3 (pin 3 of the emitter) and pin 7 of the PC connector, with the cathode of the diode connected to the PC connector.

3. In parallel with the LED input of OK 3 (pins 1 and 2), connect an additional resistor of approximately 2.2 kOhms.

2. Short-circuit LED3 (and the parallel resistor R4) using a piece of wire.
If the behavior improves with this adjustment (but is not yet perfect), you can further reduce the value of R3 from 2.2 to 1.5 kOhms (1.5 kOhms is the original design value).

Reduce the value of resistor R7 to 1.5 kΩ or 1.0 kΩ.



Best regards, Georg.
Golf VI Variant (2012) 140 tkm, CFHC Schummeldiesel


Translated on 20-10-2026, 12:55.
Back to top Profile PM Garage
OlliP
Guest




 


Free account, no CAN development support

Post06-10-2002, 20:00    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hi Ulf,

Sure, here is the translation of the text from German to English:

'This is the October issue!'
That part is supposed to work very well.
Furthermore, I also have a LINK here.

http://hal9000.vc-graz.ac.at/3rdfloor/projects/diagnose/Diagnose-Interface.htm

It should be quite good!!!!

'I'm writing 'it should be good' because I have no idea and only...'
I read about it!

Regards,
Olli.
(by the way, 'Palatinate')


Translated on 20-10-2026, 12:57.
Back to top
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post06-10-2002, 21:31    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Georg_G wrote:

I only applied the following changes that you suggested to your original version.
Quote:


For those who want to try it out in advance:

1. Insert an additional diode (cathode connected to R1) between pin 7 of the PC connector and resistor R1.

Insert an additional diode between OK 3 (pin 3 of the emitter) and pin 7 of the PC connector, with the cathode of the diode connected to the PC connector.

3. In parallel with the LED input of OK 3 (pins 1 and 2), connect an additional resistor of approximately 2.2 kOhms.

2. Short-circuit LED3 (and the parallel resistor R4) using a piece of wire.
If the behavior improves with this adjustment (but is not yet perfect), you can further reduce the value of R3 from 2.2 to 1.5 kOhms (1.5 kOhms is the original design value).

Reduce the value of resistor R7 to 1.5 kΩ or 1.0 kΩ.




Hi Georg,

Does that mean your adapter, which is similar to the 1.1 version (but without extra output transistors), works on your laptop?
Gruß Ulf
_________

MG4 Electric


Translated on 20-10-2026, 12:59.
Back to top Profile PM Garage
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post06-10-2002, 21:39    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

OlliP wrote:

Furthermore, I also have a LINK here.

http://hal9000.vc-graz.ac.at/3rdfloor/projects/diagnose/Diagnose-Interface.htm


Hi Olli,

The drawing looks practically identical to the original Noxon part at first glance.
So, therefore, nothing fundamentally new.

Thank you anyway!
Gruß Ulf
_________

MG4 Electric


Translated on 20-10-2026, 13:01.
Back to top Profile PM Garage
Georg_G
Profi-Schrauber
Profi-Schrauber


Joined: 04/12/2002
Posts: 332
Karma: +6 / -0   Thank you, like it!
Location: Freiburg im Breisgau
2012 Volkswagen Golf
Support

Post07-10-2002, 7:20    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hi Ulf,

ulf wrote:

Hi Georg,

Does that mean your adapter, which is similar to the 1.1 version (but without extra output transistors), works on your laptop?


Exactly that.

Best regards, Georg.
Golf VI Variant (2012) 140 tkm, CFHC Schummeldiesel


Translated on 20-10-2026, 13:02.
Back to top Profile PM Garage
christians
Profi-Schrauber
Profi-Schrauber


Joined: 09/05/2002
Posts: 2105
Karma: +17 / -0   Thank you, like it!
Location: Sauerland

Premium Support

Post07-10-2002, 10:33    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

The October issue of Elektor explains the fundamentals of the OBD interface.
A set of instructions for construction will be included in the November issue, starting on October 24, 2002.


Translated on 20-10-2026, 13:02.
Back to top Profile PM
Gremlin
Guest




 


Free account, no CAN development support

Post07-10-2002, 17:28    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

I skimmed the original schematic today. Everything seems to be correct for a proper RS232 implementation.
Even with a 6V level, the optocouplers should still function well (If ≈ 5mA).

I'll measure the laptop sometime when I have the chance (as soon as the portable scope is back).

I've been envisioning a CAN interface for quite some time now...

Besides the programming effort...

'The (PCMCIA) interface cards are guarded here by large, broad-shouldered men who are armed with axes... '

800 E icon_eek.gif icon_eek.gif icon_eek.gif

I guess I'll have to go and figure things out. icon_confused.gif

CU Gremlin.


Translated on 20-10-2026, 13:03.
Back to top
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post08-10-2002, 15:00    Subject: Electrode Adapters: Buy Now & Save! Quote

christians wrote:
The October issue of Elektor explains the fundamentals of the OBD interface.
A set of building instructions will be included in the November issue, starting on October 24, 2002
.

hi

I got the October issue today.

The interface with the pre-programmed microcontroller that was announced in the preview is no longer part of my (more analog, DIY) world.

I'll leave that topic to the digital enthusiasts.
Gruß Ulf
_________

MG4 Electric


Translated on 20-10-2026, 13:05.
Back to top Profile PM Garage
kfh
Guest




 


Free account, no CAN development support

Post04-02-2003, 22:53    Subject: Adapter: Elektor Solutions & Compatibility Quote

In the October issue of Elektor, the fundamentals of the OBD interface are explained.
A set of building instructions will be included in the November issue, starting on October 24, 2002.

hi

I got the October issue today.

The interface with the pre-programmed microcontroller that was announced in the preview is no longer part of my (more analog, DIY) world.

I will therefore leave that field to the digital enthusiasts.


Meanwhile, some people must have already read the November issue.
What do you think of the circuit?
Better than the tried-and-true things?

Best regards,
Karsten.


Translated on 20-10-2026, 13:07.
Back to top
BERT
Guest




 


Free account, no CAN development support

Post05-02-2003, 9:19    Subject: VAGCOM Adapter 2.0: Problems and Issues Quote

Hello everyone.

I also read the Elektor article. The pre-programmed chip used there converts the OBD protocol into ASCII. However, this chip can only translate the standardized basic vocabulary according to OBD. It does not know any manufacturer-specific commands. Furthermore, for diesel passenger cars, OBD support is only mandatory from 2003.
In short: no more VAGCOM.

AST.


Translated on 20-10-2026, 13:09.
Back to top
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Go to page: 1, 2  Next
Similar articles and topics
Topic Forum
No new posts Dimensions GT17/BV43 Turbocharger Adapter Technical Data
No new posts DIY OBD Adapter: Build Your Own Diagnostic Tool Troubleshooting & Guides
No new posts Problem with VAGCOM Adapter 2.4 Diesel Engine Technology
No new posts Another VAGCOM adapter Diesel Engine Technology
No new posts VAGCOM USB Adapter: Professional Edition Diesel Engine Technology
No new posts VAGCOM Minimal Adapter Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.