VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Defektes Mengenstellwerk und Anschleppen, Chance? | Posts 32+

 
Go to page: Previous  1, 2, 3, 4  Next
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post04-06-2012, 12:36    Subject: Quote

Does anyone have the configuration values for the firewall (FB) and possibly the pins for checking the supply voltage at the main switching device (MSTG)?
Kaum macht man es richtig, funktioniert es!


Translated on 13-10-2026, 11:49.
Back to top Profile PM Garage
DieselBär30x
Profi-Schrauber
Profi-Schrauber
Avatar-DieselBär30x

Joined: 01/17/2008
Posts: 3560
Karma: +101 / -0   Thank you, like it!
Location: MĂźnchen & Passau

Premium Support

Post04-06-2012, 14:27    Subject: Quote

To the best of my knowledge, 0.70mm +/- 0.02mm.
Even with a diameter of roughly 0.6 - 0.8 mm, it should at least start or sputter. You can immediately see if it's roughly the right size or if it's way off.

Unfortunately, I can't provide information about pin assignments off the top of my head, but others might know. icon_wink.gif

Best regards from Munich!
1. S.verlängerung: Audi A4 Avant quattro, 1,9 TDi MKB: AFN, BJ98, Vollausstattung, +VP1L
2. Moped BMW K1200RS, 130 PS, BJ98, Vollausst.
3. T5 1,9 TDI PD (AXC), BJ04 - nur Ärger!


Translated on 13-10-2026, 11:50.
Back to top Profile PM
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post04-06-2012, 17:38    Subject: Quote

The starting value is 0.71, and I am grateful for a new idea icon_smile.gif.
Does it still spray even when the MSTG doesn't have power?
Kaum macht man es richtig, funktioniert es!


Translated on 13-10-2026, 11:51.
Back to top Profile PM Garage
RedR32
Schrauber
Schrauber
Avatar-RedR32

Joined: 12/21/2008
Posts: 1071
Karma: +11 / -0   Thank you, like it!
Location: Bad Lobenstein
1998 Volkswagen Golf
Premium Support

Post04-06-2012, 18:02    Subject: Quote

klahaui wrote:

Does it actually inject something even if the MSTG doesn't have power?


No, because in that case, the terminal block on the VEP would also not be energized.
2010 Caddy kombi life 103 tdisg6 BMM KXW
reflexsilber met.


Translated on 13-10-2026, 11:51.
Back to top Profile PM Garage
DieselBär30x
Profi-Schrauber
Profi-Schrauber
Avatar-DieselBär30x

Joined: 01/17/2008
Posts: 3560
Karma: +101 / -0   Thank you, like it!
Location: MĂźnchen & Passau

Premium Support

Post04-06-2012, 18:10    Subject: Quote

Then it will probably be a bit difficult to come up with new ideas - at least on my part icon_wink.gif.

No, ESP doesn't inject anything without the MStG (German tax law), unless the MSW (mixture stroke window) is adjusted so excessively that it essentially becomes a self-runner.
But that would introduce errors into the memory, which you don't have. icon_rolleyes.gif

I would next try using a separate diesel supply and then remove the MSW (Multi-Stage Waste).
I have no idea how it behaves when the throttle valve shaft is broken, but in that case, no error codes should be logged, since the engine control unit (ECU) is still receiving signals... *peering into my crystal ball*.

Best regards from Munich!
1. S.verlängerung: Audi A4 Avant quattro, 1,9 TDi MKB: AFN, BJ98, Vollausstattung, +VP1L
2. Moped BMW K1200RS, 130 PS, BJ98, Vollausst.
3. T5 1,9 TDI PD (AXC), BJ04 - nur Ärger!


Translated on 31-10-2026, 12:35.
Back to top Profile PM
Autoservice
Profi-Schrauber
Profi-Schrauber
Avatar-Autoservice

Joined: 04/14/2012
Posts: 2130
Karma: +99 / -0   Thank you, like it!
Location: Nähe Dßsseldorf

Support

Post04-06-2012, 19:04    Subject: Quote

Quote:
No, ESP doesn't inject anything without the MStG, unless the MSW is adjusted so excessively that it becomes almost self-running.


Okay. But you could, for example, test the functionality of at least the high-pressure part (by forcefully pushing the MSW). To do this, the nozzles would need to be removed and connected to the lines.

If diesel fuel is coming from the line, it doesn't necessarily mean that the injector opening pressure is being reached, or that fuel is actually being injected.
LG, Onkel BM

*Nichts ist einfacher, als sich schwierig auszudrĂźcken......*

**Technische Fragen bitte ins Forum und nicht in mein Postfach**


Translated on 31-10-2026, 12:36.
Back to top Profile PM
RedR32
Schrauber
Schrauber
Avatar-RedR32

Joined: 12/21/2008
Posts: 1071
Karma: +11 / -0   Thank you, like it!
Location: Bad Lobenstein
1998 Volkswagen Golf
Premium Support

Post04-06-2012, 19:43    Subject: Quote

Is the starting voltage okay now? So, no more flickering AI?
Does the clutch housing align with top dead center, and are the camshaft and pump rotor alignment pins properly positioned?
Shut-off valve is okay, is fuel reaching it? When you slightly tighten the coupling nut, it should spray. You can't really detect any pressure when it's fully open.
What error codes are currently stored in the fault memory, and what are the values displayed in diagnostic data block 1 (MWB1)?
You should shed some light on this for us.
In my opinion, the quantity setting error is strongly related to the pump settings. Or WFS, no, it's not even starting up.
For those who are extremely lazy, there's also starter spray or brake cleaner available.
2010 Caddy kombi life 103 tdisg6 BMM KXW
reflexsilber met.


Translated on 31-10-2026, 12:38.
Back to top Profile PM Garage
Herbert
Profi-Schrauber
Profi-Schrauber


Joined: 06/22/2005
Posts: 4636
Karma: +1350 / -0   Thank you, like it!


Premium Support

Post04-06-2012, 21:23    Subject: Quote

Quote:
For those who are extremely lazy, there's still starter spray or brake cleaner...
Please don't. We've talked about it so many times.
Quote:
Even with a diameter of roughly 0.6 - 0.8mm, it should at least start or cough.
I agree with that.
I would still look for a cable/grounding problem or a faulty ignition switch.
hg
Herbert.
Horch A4 8K CJCD
Golf 7 DDYA
(+ Audi 80 Avant B4 1Z 475Tkm - habe ich vom ersten bis zum letzten Tag gerne gefahren)
(+ Passat Variant 32B CY 400Tkm)


Translated on 31-10-2026, 12:39.
Back to top Profile PM
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post05-06-2012, 9:21    Subject: Quote

I'm currently quite busy with work again.
I might be able to borrow an ESP this week; I suspect the problem might still be related to it.
I'll get back to you.

EDIT: Error memory is clear, module control unit unchanged, all OT markings are correct and the module can be disconnected, starting voltage is fine, no flickering instrument cluster.

If the opening pressure were insufficient, wouldn't it produce smoke and a foul odor from the back?

Next, I want to remove the nozzles so they don't just drip continuously.
Kaum macht man es richtig, funktioniert es!


Translated on 31-10-2026, 12:41.
Back to top Profile PM Garage
DieselBär30x
Profi-Schrauber
Profi-Schrauber
Avatar-DieselBär30x

Joined: 01/17/2008
Posts: 3560
Karma: +101 / -0   Thank you, like it!
Location: MĂźnchen & Passau

Premium Support

Post05-06-2012, 10:56    Subject: Quote

Hey Klaui! icon_wink.gif

As I mentioned before, I would approach troubleshooting by systematically checking each issue one by one, in a logical order, and avoid starting five projects simultaneously icon_wink.gif.
The previous owner probably told you something about "tinkering with the ESP/MSW system..."
So, that's where I would start.

Try swapping the ESP module or, even better, exchanging it.
Alternatively, feed the diesel separately and observe the return flow rate when the engine is running (wing cell pump is okay!). Then disconnect the MSW (Motor Steuergerät - Engine Control Unit) and take a look inside to see if the control cams are broken. If the MSW itself is defective or malfunctioning, there would definitely be an error message.
Measure the voltage at the rear terminal; it should read 12V when the organ is playing.

Best regards from Munich!
1. S.verlängerung: Audi A4 Avant quattro, 1,9 TDi MKB: AFN, BJ98, Vollausstattung, +VP1L
2. Moped BMW K1200RS, 130 PS, BJ98, Vollausst.
3. T5 1,9 TDI PD (AXC), BJ04 - nur Ärger!


Translated on 31-10-2026, 12:42.
Back to top Profile PM
mserge
Schrauber
Schrauber


Joined: 06/20/2005
Posts: 923
Karma: +6 / -0   Thank you, like it!
Location: Luxemburg

Support

Post06-06-2012, 14:12    Subject: Quote

Hi, have you tried to tow it or have it towed?
A4 Avant 2,5 tdi 110kw; AFB; BJ2000
4 neue Nockenwellen bei 135 tkm!!
neuer Turbo bei 200.000km
neue ESP bei 216.000km
verkauft mit 225000tkm
jetzt Renault Espace 2,0 dci 172 Initiale BJ2012
Clio 2 RS 170 PS BJ2003


Translated on 31-10-2026, 12:43.
Back to top Profile PM
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post06-06-2012, 21:51    Subject: Quote

Okay, fellow diesel engine enthusiasts, the engine is running for now.

MWB: Initially, 2.0 mg/H and 1.5V, then it sounded like a relay was switching, and I only had 1.0 mg/H and 1.2-1.3V, and the motor ran more smoothly. (Target value: 2.0-6.0 mg/H)

It's producing a lot of gray smoke, and it seems like there's a significant amount of condensation in the exhaust; it's very wet.

As soon as I enter the basic settings in the MWB 000, the engine almost stalls, and the dynamic function block doesn't display any values.

The turbo also whistles very loudly.

Can you make sense of these values? I'm almost certain that the Facebook ad isn't quite right.

Greetings.
Kaum macht man es richtig, funktioniert es!


Translated on 31-10-2026, 12:44.
Back to top Profile PM Garage
Herbert
Profi-Schrauber
Profi-Schrauber


Joined: 06/22/2005
Posts: 4636
Karma: +1350 / -0   Thank you, like it!


Premium Support

Post06-06-2012, 22:06    Subject: Quote

Hi,
Quote:
...MWB: Initially 2.0mg/H and 1.5V, then it sounded like a relay was switching, as I only had 1.0mg/H and 1.2-1.3V
. The motor is running extremely rich. MSW is misadjusted. Be glad that it didn't rev up.
Quote:
...As soon as I enter the basic settings in the MWB 000, the engine almost stalls, and in the dynamic function block, it doesn't display any values.
EZP is completely wrong. What is displayed in MWB 0, field 2 and 9? Of course, the measurement only makes sense when the engine temperature is above 85°C.
hg
Herbert.
Horch A4 8K CJCD
Golf 7 DDYA
(+ Audi 80 Avant B4 1Z 475Tkm - habe ich vom ersten bis zum letzten Tag gerne gefahren)
(+ Passat Variant 32B CY 400Tkm)


Translated on 31-10-2026, 12:46.
Back to top Profile PM
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post06-06-2012, 22:12    Subject: Quote

How do I properly configure the MSW in this case?
I can only announce the MWB 0 tomorrow evening.

EDIT: Also, it also starts very poorly; it only starts if you give it gas.
EDIT 2: Error memory still empty.
Kaum macht man es richtig, funktioniert es!


Translated on 31-10-2026, 12:48.
Back to top Profile PM Garage
RedR32
Schrauber
Schrauber
Avatar-RedR32

Joined: 12/21/2008
Posts: 1071
Karma: +11 / -0   Thank you, like it!
Location: Bad Lobenstein
1998 Volkswagen Golf
Premium Support

Post06-06-2012, 22:24    Subject: Quote

klahaui wrote:
How do I properly configure the MSW in this case?


/viewtopic.php?t=5517
http://www.dieselschrauber.de/Solldaten_4_Zylinder_VE.html
2010 Caddy kombi life 103 tdisg6 BMM KXW
reflexsilber met.


Translated on 31-10-2026, 12:48.
Back to top Profile PM Garage
klahaui
Profi-Schrauber
Profi-Schrauber
Avatar-klahaui

Joined: 08/13/2009
Posts: 1102
Karma: +125 / -0   Thank you, like it!
Location: Vogtland, Land der Berge
2019 Volkswagen Golf
Premium Support

Post07-06-2012, 7:11    Subject: Quote

What surprises me is why I initially had 2.0 mg/H, and then suddenly only 1.0 mg/H?
It adjusted simultaneously with a switching relay or similar device.
The target value is 2.0-6.0 mg/H. Should I take the average of 4 in this range?
Unfortunately, I wasn't able to perform a test run before disassembling it.
Kaum macht man es richtig, funktioniert es!


Translated on 31-10-2026, 12:49.
Back to top Profile PM Garage
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Go to page: Previous  1, 2, 3, 4  Next
Similar articles and topics
Topic Forum
No new posts Quantity setting device and control path generator: Function Technical Articles
No new posts Faulty Wheel Bearing? Symptoms & Repair. Transmission, Chassis, Body & Interior
No new posts Faulty Control Unit? Get it Fixed Now! On-Board Diagnostics (OBD)
No new posts Faulty glove compartment lock (8E5) Transmission, Chassis, Body & Interior
No new posts SCR Control Unit Replacement: Coding Required? Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.