VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Engine Flush: How to Properly Water Your Engine

 
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
Diesel-Dirk
Guest




 


Free account, no CAN development support

Post10-05-2002, 19:24    Subject: Engine Flush: How to Properly Water Your Engine Quote

Unfortunately, I was driving a bit too fast and ended up going through a huge puddle. The engine stalled and that was it.
After a short pause, the starter motor stopped working. Suspected cause: short circuit -> dead battery. However, that wasn't the problem. Removed the air filter -> it was soaking wet!

Luckily, a friendly hardware store owner next door lent me some tools from his shelves.

'I removed the spark plugs, and the engine immediately started turning again and spitting out water. Then I put the spark plugs back in and ran the engine as a naturally aspirated (non-turbo) engine. I quickly drained a cup of water from the intercooler and then reassembled everything. After a short period of sputtering and water coming out of the exhaust, the car is running again. So far, I haven't noticed any loss of power.'


What long-term consequences can I expect after such an action?

Has anyone else experienced something similar?


Translated on 15-10-2026, 5:43.
Back to top
Michael II
Profi-Schrauber
Profi-Schrauber


Joined: 04/12/2002
Posts: 1132
Karma: +3 / -0   Thank you, like it!
Location: Stuttgart

Support

Post10-05-2002, 21:39    Subject: Engine Flush: How to Properly Water Your Engine Quote

Hello,

Just a quick question, by the way:

How deep was the puddle? (Was it a normal puddle or a small lake icon_cool.gif)
Tschüss

Michael II


Translated on 15-10-2026, 5:45.
Back to top Profile PM
Diesel-Dirk
Guest




 


Free account, no CAN development support

Post11-05-2002, 16:50    Subject: Engine Flush: How to Properly Water Your Engine Quote

It was quite a deep puddle. The wave in front of the car washed leaves between the hood and the grill.


Translated on 15-10-2026, 5:45.
Back to top
Michael II
Profi-Schrauber
Profi-Schrauber


Joined: 04/12/2002
Posts: 1132
Karma: +3 / -0   Thank you, like it!
Location: Stuttgart

Support

Post12-05-2002, 8:46    Subject: Engine Flush: How to Properly Water Your Engine Quote

Hello,

I would definitely recommend an oil change. Also, check the other containers for any signs of water (coolant, power steering fluid, etc.).
Tschüss

Michael II


Translated on 15-10-2026, 5:45.
Back to top Profile PM
Diesel-Dirk
Guest




 


Free account, no CAN development support

Post12-05-2002, 11:28    Subject: Engine Flush: How to Properly Water Your Engine Quote

I've also been thinking about getting an oil change.

Water traces in the coolant?
No water should have gotten into the power steering fluid.

I'm more concerned that my turbo might be upset about the whole situation. I'm not sure if it got a large stream of fluid or just a few drops. There was so much fluid inside the engine that it wouldn't even turn over with the starter.


Translated on 15-10-2026, 5:46.
Back to top
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post12-05-2002, 13:48    Subject: Water Damage? Get Help Now! Quote

Diesel-Dirk wrote:
I'm more concerned that my turbo might be upset about the incident. I don't know if it received a large stream or just droplets. There was so much inside the engine that it wouldn't even turn over with the starter.


Hi.

The water has long since drained out of the charger. If it's working normally now, I don't think there should be any late-stage damage.

If I were in your position, my biggest concern would be the engine: if the piston movement is stopped by a water cushion, it often leads to "water hammer." The compressing piston hits the "water wall," and the sudden deceleration of all moving parts in the engine can cause connecting rods to bend, etc.
It typically occurs as a result of defective cylinder head gaskets.
Gruß Ulf
_________

MG4 Electric


Translated on 15-10-2026, 5:48.
Back to top Profile PM Garage
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Similar articles and topics
Topic Forum
No new posts AJM Engine: Rattling, Power Loss, Black Smoke Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts AFB Engine Overview Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts 2.0 TDI Engine Coolant Leak Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Smoking engine after engine/turbo replacement Diesel Engine Technology
No new posts TDI Engine with Gas Transmission: Possible? Diesel Engine Technology
No new posts 1Z Motor Audi 80 B4: Make the engine more fuel-efficient Diesel Engine Technology
No new posts AEL engine in T4 - Ex-ACV Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.