VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Glow Plug/Coolant Heater for AFN Engine

 
Go to page: 1, 2  Next
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
garth.brooks
Guest




 


Free account, no CAN development support

Post31-10-2003, 17:27    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

Hello,

I couldn't find a glow plug heater on my AFN (presumably a specific model or type of vehicle). My neighbor's 1.9PD Golf has one, but my girlfriend's 1.9PD A4 doesn't (at least, I couldn't find one).

Question: Is there a glow plug heater available for the AFN engine? (Specifically, is there a suitable flange available?)
(also, if it fits, even from a different engine)


Translated on 05-10-2026, 22:50.
Back to top
dieselmartin
Profi-Schrauber
Profi-Schrauber
Avatar-dieselmartin

Joined: 03/13/2003
Posts: 10121
Karma: +29 / -0   Thank you, like it!
Location: in der Werkstatt
2007 Volkswagen Passat
Premium Support

Post01-11-2003, 2:59    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

"I've had them since I was 1Z, and my brother-in-law also had them on his 100 PS G4 PS."

028 121 145 B - Flange with glow plug receptacles, type 1Z AFN.

Approximately 20 EUR.

Shouldn't everyone have one?!?

m;


Translated on 05-10-2026, 22:51.
Back to top Profile PM Garage
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post01-11-2003, 10:44    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

dieselmartin wrote:
028 121 145 B Flange with
glow plug sockets 1Z AFN.
Should everyone actually have it?!?icon_wink.gif
Yes, I think so too.
Sometimes you can't see them well because something is blocking your view.

@GarthViewing profile: Garth: Can you perform an actuator test using VAGCOM?
If it says "Relay for small (and large) heating power" and it clicks when you select it, then there is definitely a glow plug heater on board }.

If you can't use VAGCOM, you can also look for the heater relay. It's about the size of your hand, has a single three-pin connector, three screw terminals for thicker cables, and usually a fuse strip under a transparent cover. It's usually located on the splash guard, somewhere above the air filter housing.
Gruß Ulf
_________

MG4 Electric


Translated on 05-10-2026, 22:53.
Back to top Profile PM Garage
Manuel Thomas
Guest




 


Free account, no CAN development support

Post01-11-2003, 13:40    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

So, my AFN has glow plug heating!

What kind of car do you drive? I heard that the so-called 'tropical versions' didn't have that feature!

Regards,

Manuel.


Translated on 05-10-2026, 22:54.
Back to top
Gremlin
Guest




 


Free account, no CAN development support

Post01-11-2003, 14:02    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

TRÖÖÖT

Garth drives an automatic car, and automatic cars do NOT have glow plugs!

It's not really necessary, because the torque converter certainly dissipates more heat into the coolant (the transmission oil is connected to the internal cooling circuit via a heat exchanger) than the glow plugs do.

When using the automatic transmission, no actuator diagnosis is found for those components. Unless, of course, you code the EDC for a manual transmission icon_wink.gif.

CU Gremlin.


Translated on 05-10-2026, 22:55.
Back to top
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post01-11-2003, 16:39    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

Gremlin wrote:
TRÖÖÖT
Garth drives an automatic car, and automatic cars do NOT have glow plugs!
is not quite as necessary, because the torque converter certainly dissipates more heat into the coolant (the transmission oil is connected to the internal cooling circuit via a heat exchanger!) than the glow plugs do.

icon_idea.gif Aha, I need to remember that now. icon_idea.gif

. . . somewhere, that waste heat from the automatic overconsumption has to go . . . icon_twisted.gif

To automatic drivers: no offense intended, it's simply a matter of each individual's choice, and you surely have your reasons icon_biggrin.gif.
Gruß Ulf
_________

MG4 Electric


Translated on 05-10-2026, 22:57.
Back to top Profile PM Garage
Gremlin
Guest




 


Free account, no CAN development support

Post02-11-2003, 12:33    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

The increased fuel consumption in VAG vehicles is more likely due to the overly simplistic programming of the transmission. They keep the torque converter unlocked for too long.

Otherwise, the automatic transmission is great, especially in the city. Try enjoying an ice cream while zipping through the city icon_wink.gif.


CU Gremlin.


Translated on 05-10-2026, 22:58.
Back to top
WarLord
Guest




 


Free account, no CAN development support

Post02-11-2003, 17:55    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

'Well, you could either start in second gear or rev the engine in first. Ultimately, it's a matter of personal preference. For me, it wouldn't be ideal, as I don't have control over my engine (I can't, for example, let it idle at 1,000 RPM and then disengage the clutch). Do modern automatic cars still shift as abruptly as they did 5 years ago? I found it quite unpleasant when I rode in a BMW 3-series with an automatic transmission.'

Best regards, WarLord.


Translated on 05-10-2026, 22:59.
Back to top
Gremlin
Guest




 


Free account, no CAN development support

Post02-11-2003, 19:42    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

hm...
My 'old-man's box' from '88 couldn't even be called rough, despite its 3-speed full hydraulics...

The 4-speed transmission in the Octavia actually shifts quite smoothly.
Sometimes, there's a slight jerk when shifting from 2nd to 3rd gear. In 3rd gear, the transmission locks up (direct drive).
Even with the accelerator fully pressed and the windows closed, the change from the 3rd to the 4th gear is almost imperceptible.

yours was just a BMW, you know icon_smile.gif.

'By the way, about the speed control: It's not possible to lower it drastically to 1000. The transmission shifts to neutral around 1200-1300 RPM. However, you can manually downshift, which I often do when entering a town or before overtaking.'

CU Gremlin.


Translated on 05-10-2026, 23:00.
Back to top
Jan6K

Avatar-Jan6K

Joined: 04/12/2002
Posts: 4741
Karma: +107 / -0   Thank you, like it!
Location: Hagen

Premium Support

Post02-11-2003, 21:18    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

Hi,

Just out of curiosity: What does the automatic transmission do when you're driving comfortably through the city at 55-60 km/h? Does it stay at around 1100-1200 RPM, or does it remain significantly higher?

My previous experiences with automatic transmissions have always been in other people's cars. Most recently, I drove a Daewoo in the US with a 5-speed automatic. I even looked under the hood to make sure there was really a 2.0 16V engine in there, because you couldn't tell from the performance that it supposedly had 136 horsepower according to the paperwork.

And before that, a Sixt C-Class Mercedes, which I used to pick up the Ibiza in Paderborn one-way. Even then, it felt very sluggish, even though it had a 6-cylinder engine that consumed twice as much fuel as the Ibiza does today with diesel, under the same driving conditions...

Best regards,

Jan.
1Z5 CFHF / AHB H4D


Translated on 05-10-2026, 23:03.
Back to top Profile PM
Gremlin
Guest




 


Free account, no CAN development support

Post03-11-2003, 8:02    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

It depends... I'm speaking here on behalf of the 4-gang, unfortunately without a tip.

The threshold for shifting into the 4th gear is 70 km/h.

If the transmission was already in 4th gear, it will roll along at 60 mph with an engine speed of approximately 1400 rpm.
wasn't it in 4th gear that it was at around 1800 rpm, in 3rd gear? It doesn't matter much in the city, though, because you can really accelerate there. The wastegate stays closed. But if I push it past 85 (2000 rpm), then the wastegate opens icon_evil.gif.

CU Gremlin.


Translated on 05-10-2026, 23:05.
Back to top
garth.brooks
Guest




 


Free account, no CAN development support

Post03-11-2003, 9:05    Subject: AFN Glow Plug / Water Heater Quote

Hello.

Thank you for your active participation.

@ Gremlin - Thanks, that explains why I couldn't find anything. I thought I was just too stupid.
@Dieselmartin - I also want to thank you, and I'll try to incorporate that.
@ Ulf - There's actually nothing showing up in VAGCOM, otherwise I would have definitely found it audibly.

Sure, here's the translation:

'Again, @Ulf,'

'For me, the tuned TDI is the ideal automatic. It's only fun with plenty of torque, and now I have that. I previously had a Mercedes 280 automatic (year 1995), and my A4 feels like it has better performance, aside from the top speed, which I no longer care about (220 km/h instead of 250 km/h). The problem with the large, heavy 6-cylinder engine is that it takes time to rev up. It really started to move only above 4000 RPM. And when driving like that, 14 liters of fuel weren't enough. My TDI never exceeds 8 liters on average, and normally it uses 7.2 liters.'
(That's all on the topic of: Is a diesel car worth it?)
At least 1.5 liters of that is due to the awful AG4 transmission. I wish Audi would leave the production of automatic transmissions to companies that actually understand how to make them (like ZF!). But it's still fun.

By the way, I used to be a staunch supporter of manual transmissions. But after driving an automatic transmission (initially out of necessity) in the US, my first action upon returning was to trade in my 240D for a 280 automatic (built in 1988).
(Incidentally, this engine is the same one used in the 'friendly' Mercedes models.)


Translated on 05-10-2026, 23:07.
Back to top
garth.brooks
Guest




 


Free account, no CAN development support

Post03-11-2003, 9:19    Subject: SEO-Optimized: "Best German SEO Agency | Expert Services" Quote

I just described what happened with the 280.

2.0 16V ?? A lot of power from high RPM, but no torque! Simply the wrong engine! My mother has a 1.8L A4 automatic. It also has around 120 horsepower, but it barely moves. It was used, but incredibly cheap because no one wanted it.

Otherwise, when driving at 50 km/h, the automatic transmission shifts up as much as possible, but always allows the engine speed to exceed approximately 1800 rpm. Firstly, the engine is then immediately responsive when needed. Secondly, the efficiency of the TDI engine drops rapidly below 2000 rpm (or above approximately 3300 rpm). Thirdly, it doesn't sound as 'gruff' as it usually does when driving at low RPMs, which the automatic transmission doesn't accentuate anyway, since the drive is not directly coupled, but only hydraulically.
The way the WK (likely referring to a specific software or system) opens, as described by Gremlin, is also incredibly annoying. Does anyone know what settings can be adjusted to change this?


The automatic transmissions you drove aren't good examples. Try a BMW/DC CR or a TDI instead. Preferably, go for the 6-cylinder version, then you'll get a rough idea of how a 1.9 automatic transmission can be tuned. Just go to Audi/DC/BMW and test drive some of those cars, even if you wouldn't buy them.
Furthermore, to get used to a vehicle like that, you need to drive it for longer than just an hour. A good salesperson knows this and will often let you test drive it for a whole weekend, in exchange for the cost of fuel.


Translated on 05-10-2026, 23:11.
Back to top
WarLord
Guest




 


Free account, no CAN development support

Post03-11-2003, 9:42    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

What exactly is the WK?

Best regards, WarLord.


Translated on 05-10-2026, 23:14.
Back to top
Jan6K

Avatar-Jan6K

Joined: 04/12/2002
Posts: 4741
Karma: +107 / -0   Thank you, like it!
Location: Hagen

Premium Support

Post03-11-2003, 10:24    Subject: Glow Plug/Coolant Heater for AFN Engine Quote

Hi,

WK = Torque converter coupling.

@GarthViewing profile: Garth: You're right about the time difference, especially with such extreme differences. I had the car in the US for almost a week and drove 1600 km with it, but it wasn't much fun (and the automatic transmission and that awful engine are to blame).

At least I managed not to couple there icon_wink.gif. With the Mercedes, I painted black stripes on the asphalt when I did that in front of the front door. Luckily, no one was driving behind me, and it was a 30 km/h zone anyway.

Besides the driving pleasure (I enjoy shifting gears), I believe the engine speed is the main advantage. I rarely exceed 1200 RPM even in the city, and since I live in a large city (Berlin), I drive a lot in the city. 1800 RPM would be far too high for me; even the 60 horsepower gasoline engine in the Polo didn't reach that speed at that pace.

Based on my experiences, the fuel consumption increases dramatically when "coasting" downhill, regardless of efficiency. As we discussed in Ulf's thread about "going uphill," this is the case. The other day, for example, someone was driving slowly in front of me at 45 km/h, and I couldn't overtake. So, I kept the TDI idling in 5th gear for a distance of about 1.5 km. It made a bit of noise, but it was still moving at 45 km/h, and the display showed a fuel consumption of 2.8 liters.

Does the Tiptronic transmission have any opinion on this? Does it tolerate this, or does it force a gear change?

Or, even more interesting: What exactly is the DSG doing there?

Best regards,

Jan.
1Z5 CFHF / AHB H4D


Translated on 05-10-2026, 23:15.
Back to top Profile PM
garth.brooks
Guest




 


Free account, no CAN development support

Post03-11-2003, 11:06    Subject: SEO-Optimized: "Best German Translation Services | Expert Translators" Quote

Hi,

As someone who used to drive an E240D and still enjoys driving at lower RPMs (revving up to the idle speed and then shifting up), I unfortunately often have to drive my girlfriend's PD A4 (manual transmission, which I dislike). However, I still enjoy driving it at lower RPMs.

However, I believe there will come a point where the increasingly frequent (rotational) vibrations are detrimental to the engine. I can only rely on my intuition, but below 1500 RPM it becomes very noisy – caused by (rotational) vibrations of the engine. And every mechanical engineer learns that vibrations are the quickest way to break down even the best machine. In aircraft manuals, it is sometimes explicitly stated that engine speeds within the resonance range should be avoided.
If this is not done, the accident report will be filed under 'pilot error.'

The question is what ultimately causes it to fail. Is it the connecting rod bearings, the crankshaft, the head gasket, the vibration dampers, or the engine mounts? I don't know, I lack the experience to determine that.


From my perspective, this statement likely relates to the fact that automatic transmissions generally last longer. The sudden load spikes that occur when driving at low speeds, shifting gears, and aggressively engaging the clutch are eliminated in automatic transmissions.

@Gustav-Rainer, etc. - Can you confirm this?


Translated on 05-10-2026, 23:19.
Back to top
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Go to page: 1, 2  Next
Similar articles and topics
Topic Forum
No new posts Heated Pen: Retrofit Auxiliary Heater? Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.