VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Diesel Injector Timing Question

 
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
fricki
Blaumann
Blaumann


Joined: 03/03/2005
Posts: 29
Karma: +7 / -3   Thank you, like it!


Free account, no CAN development support

Post17-03-2005, 8:06    Subject: Diesel Injector Timing Question Quote

I have a question for you.

I've owned a Vento, model year 1994, with a 1Z engine for quite some time.

I've now started to delve into the engine control unit (ECU) and, of course, that also includes learning about VAG-COM.

Since my Vento is shaking quite a bit at idle, I checked the TDI timing. It's completely wrong on my car.

Can someone please help me understand what makes sense here so I can get it back to a proper state.

As I understand it, the injection is happening too late. Do you think it makes sense to try to fix this through software using VAG-COM, or should I start adjusting the pump mechanically?

I've attached the photo.

Thank you very much.



einspritz.JPG
 Description:
 Diesel Injector Timing Question
 File size:  105.15 KB
 Viewed:  5061 times

einspritz.JPG



Translated on 02-11-2026, 19:16.
Back to top Profile PM
dieselmartin
Profi-Schrauber
Profi-Schrauber
Avatar-dieselmartin

Joined: 03/13/2003
Posts: 10121
Karma: +29 / -0   Thank you, like it!
Location: in der Werkstatt
2007 Volkswagen Passat
Premium Support

Post17-03-2005, 8:13    Subject: Diesel Injector Timing Question Quote

I would first try adjusting it using software and then compare the results before and after to see how effectively the injection start control in block 004 can be adjusted -> Basic Settings.

If it's not advancing far enough automatically, you might have to adjust it manually.

That has nothing to do with the jerky movement of a 1Z.

Because the stuttering is caused by (unrelated) quantity setting devices.

m;
Transparency, Teamwork
... there was another T.

I don't know what the f*ck it was.


Translated on 02-11-2026, 19:18.
Back to top Profile PM Garage
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post17-03-2005, 8:42    Subject: Diesel Injector Timing Question Quote

dieselmartin wrote:
I would first try adapting it through software and then compare the results before and after to see how far the injection start control in Block 004 can be adjusted -> Basic Settings
.
Um... in the basic settings, the injection start control is already set to the late-impact position, meaning that an adaptation wouldn't have any effect.

Es sei denn, man setzt das gesamte Kennfeld für den Fahrbetrieb per Adaption so weit nach spät, wie die Pumpe zufällig falsch steht. Fr"in the spirit of:"
"If a target value of 15°vOT is not achievable, I will set the target to 10°vOT and be satisfied with the fact that the system can be adjusted to 10°."
But it can't be that, right?

Judging by the image (assuming the NBF is intact), the pump is simply installed too late.
Typical symptoms would include sluggish acceleration at high RPMs when using full throttle, and (in my previous AFN model) very difficult starting when the engine is cold.
Gruß Ulf
_________

MG4 Electric


Translated on 02-11-2026, 19:19.
Back to top Profile PM Garage
dieselmartin
Profi-Schrauber
Profi-Schrauber
Avatar-dieselmartin

Joined: 03/13/2003
Posts: 10121
Karma: +29 / -0   Thank you, like it!
Location: in der Werkstatt
2007 Volkswagen Passat
Premium Support

Post17-03-2005, 8:59    Subject: Diesel Injector Timing Question Quote

Hi Ulf,

As I was typing this, I already thought it would be misunderstood.

I'm referring to the basic settings in block 004. My temperature sensor is reading a value that's too low (it's supposed to read 17 degrees, but it's reading around 15 degrees), which sounds like the air conditioning unit is running as if it were set to 27 degrees.
/viewtopic.php?t=7709&highlight=aku

You can tell that it's still quite early because it takes a long time for the engine to reach 15 degrees Celsius from its idle state (target: 3.1 degrees late / actual: approximately 0 degrees).
The basic settings in 000 are easily accessible.

Sorry, that was my mistake (in wording).
m;
Transparency, Teamwork
... there was another T.

I don't know what the f*ck it was.


Translated on 02-11-2026, 19:21.
Back to top Profile PM Garage
lappen
Guest




 


Free account, no CAN development support

Post17-03-2005, 9:30    Subject: Diesel Injector Timing Question Quote

Hmmmmm....

I would loosen and rotate the pump until the injection timing is correct (of course, using VAG-COM to monitor and adjust it constantly). This is the proper way to adjust it, and it's also the method prescribed by VAG. It only requires loosening 3-4 screws.


Translated on 02-11-2026, 19:23.
Back to top
fricki
Blaumann
Blaumann


Joined: 03/03/2005
Posts: 29
Karma: +7 / -3   Thank you, like it!


Free account, no CAN development support

Post01-04-2005, 21:41    Subject: Diesel Injector Timing Question Quote

Could you please explain the adaptation in a little more detail?

I am logging into the control unit with the code 12233.
Go to channel 4, which controls the injection timing, and then enter progressively lower values.
Looking at my curve, I could almost assume that I'm injecting too late and using too little [medication]. Have I correctly interpreted this?

Thank you for your help!!


Translated on 02-11-2026, 19:24.
Back to top Profile PM
ulf
Profi-Schrauber
Profi-Schrauber


Joined: 04/13/2002
Posts: 11058
Karma: +18 / -0   Thank you, like it!
Location: Saarland
2023 MG ZS
Premium Support

Post01-04-2005, 22:23    Subject: Diesel Injector Timing Question Quote

fricki wrote:
Could you please explain the adaptation in a little more detail?

I am logging into the control unit with the code 12233.
Go to channel 4, which controls the injection timing, and then enter progressively lower values.

"However, by adjusting the damper, you shift the entire target characteristic curve during operation."
It doesn't really make sense on its own - unless it's used in conjunction with a tuning, or to compensate for incorrect installation of the sensor ring or sensor.

Quote:
Looking at my curve, I could almost assume that I'm injecting too late and using too little. Have I understood that correctly?

Too late, yes (as you can also see in the Screenshot below icon_lol.gif), and if there's too little, the engine would stop.
Gruß Ulf
_________

MG4 Electric


Translated on 02-11-2026, 19:25.
Back to top Profile PM Garage
fricki
Blaumann
Blaumann


Joined: 03/03/2005
Posts: 29
Karma: +7 / -3   Thank you, like it!


Free account, no CAN development support

Post03-04-2005, 18:36    Subject: Diesel Injector Timing Question Quote

So, would the mechanical solution be the best solution ("rotating" the pump!)?


Translated on 02-11-2026, 19:26.
Back to top Profile PM
dieselschrauber
Administrator
Administrator
Avatar-dieselschrauber

Joined: 04/12/2002
Posts: 18135
Karma: +804 / -0   Thank you, like it!
Location: St.Gallen
2018 Volkswagen T6 Consumption


Post03-04-2005, 21:52    Subject: Diesel Injector Timing Question Quote

It is the only correct solution icon_smile.gif.


Translated on 02-11-2026, 19:26.
Back to top Profile PM WWW Garage
kossmann
Blaumann
Blaumann


Joined: 04/20/2002
Posts: 188
Karma: +5 / -0   Thank you, like it!

2016 Audi Q3
Premium Support

Post12-02-2008, 14:14    Subject: Diesel Injector Timing Question Quote

"I'm experiencing something similar, and I suppose I'll have to address this issue as well."

The water pump needs to be replaced with the engine running and hot (>90°C), right? What's the best way to do it without burning your fingers (gloves are probably a must) or getting your hands caught in the timing belt (which is likely to happen quickly with gloves on)?

The rest should be found in the specialized article icon_wink.gif.


Translated on 02-11-2026, 19:27.
Back to top Profile PM Email Garage
dieselmartin
Profi-Schrauber
Profi-Schrauber
Avatar-dieselmartin

Joined: 03/13/2003
Posts: 10121
Karma: +29 / -0   Thank you, like it!
Location: in der Werkstatt
2007 Volkswagen Passat
Premium Support

Post12-02-2008, 14:18    Subject: Diesel Injector Timing Question Quote

with the engine running?

Okay, if you have the same gripping power in your fingers as three M8 screws, then try doing that.

I would not interfere with a running engine.

10 hires.
20 trade fairs.
30 if (result != good) goto 10
40 feddisch.

m;
Transparency, Teamwork
... there was another T.

I don't know what the f*ck it was.


Translated on 02-11-2026, 19:28.
Back to top Profile PM Garage
kossmann
Blaumann
Blaumann


Joined: 04/20/2002
Posts: 188
Karma: +5 / -0   Thank you, like it!

2016 Audi Q3
Premium Support

Post12-02-2008, 14:26    Subject: Diesel Injector Timing Question Quote

I thought that while twisting, one would keep an eye on the TDIgraph display, which would only be possible if the engine is running.

Approximately how many degrees and in which direction would "fricki" need to rotate before restarting the engine and checking it?


Translated on 02-11-2026, 19:29.
Back to top Profile PM Email Garage
T3Surfer
Profi-Schrauber
Profi-Schrauber


Joined: 09/17/2004
Posts: 1833
Karma: +34 / -0   Thank you, like it!
Location: Frankurt
2001 Seat Toledo
Premium Support

Post12-02-2008, 20:41    Subject: Diesel Injector Timing Question Quote

I personally do it with the engine running without disconnecting the timing belt! Loosen the 3 screws on the timing belt side, loosen the 4th screw with the lock nut on the high-pressure side, use a pry bar or similar, place a wooden block between the pry bar and the fuel injection pump, and check with a 1551 or VAG-COM to see how it changes until you reach the optimal center point. Everything should be correct without touching the pry bar. Turn off the engine, tighten all screws, check again. If everything is correct, loosen all the union nuts of the fuel injection pump and injectors, and then tighten them again, so that the lines are relaxed! Otherwise, they could break later. icon_eek.gif I don't need gloves because the fuel injection pump isn't that hot!
NA,Gehörlose wie ich können auch Schrauben! Ihr HÖRT ich FÜHLE! T3 TD EX-JX Jetzt 1Z mit 122PS und Renaultgetriebe Golf II TD Bj 84 512Tkm Passi 35I 1Z 468Tkm--> Seat Toledo AHF-- Toledo ARL 477Tkm mit Spritspartuning icon_wink.gif 99er T4 Syncro-Cross 100800km grad eingefahren


Translated on 02-11-2026, 19:30.
Back to top Profile PM Email Garage
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Similar articles and topics
Topic Forum
No new posts AFN: Injection Timing & Turbo Pressure - Questions? Diesel Engine Technology
No new posts T4 Diesel Pump: Replacement & Repair Diesel Engine Technology
No new posts Diesel Pump Diagnosis: Troubleshooting & Repair On-Board Diagnostics (OBD)
No new posts Diesel Pump Springs: Function & Replacement Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.