VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

TDI: How Fast to 90°C? (96 kW)

 
Go to page: 1, 2  Next
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Transmission, Chassis, Body & Interior
Author Message
pschaefer
Blaumann
Blaumann


Joined: 08/21/2002
Posts: 300
Karma: +3 / -0   Thank you, like it!


Premium Support

Post20-12-2002, 23:08    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hello!

My Golf IV with a 96 kW PD-TDI engine doesn't reach its operating temperature of 90°C until after about 25 km, even when the temperature is -5°C.
My old 85 kW engine was much faster.

Given these outdoor temperatures, it's terrible (and it's only going to get worse).
(Just in case it ever drops to -10°C...) How long does it take for you?

What can be done about it?

Regards,

Peter.


Translated on 23-10-2026, 17:30.
Back to top Profile PM
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post21-12-2002, 7:49    Subject: TDI: How Fast to 90°C? (96 kW) Quote

pschaefer wrote:
Hello!

My Golf IV with a 96 kW PD-TDI engine doesn't reach its operating temperature of 90°C until after about 25 km, even when the temperature is -5°C.
My old 85 kW engine was much faster.

Given these outdoor temperatures, it's terrible (and it's only going to get worse).
(Just in case it gets down to -10°C...) How long does it take for you?


That's just the way it is when you drive a car with extremely high efficiency. The higher the efficiency, the less waste energy (heat) is produced.
"With my AXR, it takes about 20 kilometers to reach 90°C (without preheating). However, if I preheat it, it only takes about 5-10 kilometers to reach that temperature (measured at -7°C)."

Quote:

What can be done about it?


Preheat.
Take a look inside here: http://www.dieselschrauber.de/heizer.html
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:32.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post21-12-2002, 14:26    Subject: Warm-up Time: How to Reduce It Quote

Hi,

@pschaefer:
While 25 km is definitely a very long distance, as long as it reaches 90 degrees Celsius during normal operation, you can be relatively sure that, for example, the thermostat is not defective.
My 2.5 AAT also needs 20-25 km in this weather. But it also has to heat up a bathtub full of coolant...

@bertil:
That's a perfect timing, you bringing up these electric heaters.
I'm considering whether to install something like that instead of the incredibly expensive auxiliary heater.
Do you think something like that would also be useful for the 2.5?
Or would you have to preheat it for hours until the coolant reaches the proper temperature?
After all, it draws quite a bit of power from the outlet.


Translated on 23-10-2026, 17:35.
Back to top
pschaefer
Blaumann
Blaumann


Joined: 08/21/2002
Posts: 300
Karma: +3 / -0   Thank you, like it!


Premium Support

Post21-12-2002, 16:21    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hm, I always thought TDIs had some kind of electric component.
Auxiliary heating (a few glow plugs)...

Probably not, right? Or at least, it probably won't do anything...

Okay, I'll take a look at some supplemental heaters.


Translated on 23-10-2026, 17:36.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post21-12-2002, 16:52    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hi,

Yes, that's correct.
But first, they are quite weak, and second, they only provide heating during the worst cold-start phase.
I'm not sure, for example, whether my old AAT even has a glow plug heater.


Translated on 23-10-2026, 17:37.
Back to top
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post21-12-2002, 20:03    Subject: Warm-up time: How to optimize it Quote

Markus H. wrote:
@bertil:
That's a perfect timing, you bringing up these electric heaters.
I'm considering whether to install something like that instead of the incredibly expensive auxiliary heater.
Do you think something like that would also be useful for the 2.5?
Or would you have to preheat it for hours until the coolant is hot?
After all, it draws quite a bit of power from the outlet.


"No problem with the 2.5 either!!"
My brother had this in his 2.3L 5-cylinder gasoline engine, and it worked great!
The electrical power rating of the auxiliary heater is 550 or 600 watts (depending on the model). Therefore, with a heating time of one hour, the electricity consumption remains within reasonable limits.

Unfortunately, I can't comment on what happens when the car is parked outside, as I have a garage space (but still use the pre-heating function).
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:38.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post21-12-2002, 21:36    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hi Bertil!

Mine also has its own dwelling (=garage) icon_smile.gif.
That's why I also think that an electric heater is more useful than a standing heater.
The only disadvantage is, of course, that I don't have any preheating available in the afternoon/evening for the return journey.
Have you ever had any problems with that?
(I think that a complex auxiliary heating system is more likely to have problems than a Calix or Waeco pre-heater.)


Translated on 23-10-2026, 17:40.
Back to top
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post22-12-2002, 9:26    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Markus H. wrote:
...
Mine also has its own dwelling (=garage) icon_smile.gif.
That's why I also think that an electric heater is more useful than a standing heater.

Of course, a standing heater is problematic in this situation, and an electric heater is definitely better (and cheaper).
Quote:

The only disadvantage is, of course, that I don't have any preheating available in the afternoon/evening for the return journey.

das ist nicht ganz so schlimm, aber aus dem warmen Bett ins eisekalte nicht warmwerdende Auto ... Brrrrr.
Quote:

Have you ever had any problems with that?
(I think that the likelihood of problems is probably higher with a complex auxiliary heater than with a Calix or Waeco pre-heater)
.

Problems? With an immersion heater? I can't imagine there would be any problems with it.
However, there are two problems:
1 - Don't forget to remove the charging cable. When you're still half-asleep in the morning, it's easy to miss (and it can cause expensive damage). That's why I keep my charging cable right in front of the windshield, and I double-check it before I drive away. Alternatively, you can mount it in a way that it can easily be detached.
2 - Power outage at night, and the timer is stuck. Use a timer with a backup power supply (it's more expensive, but it's worth it).
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:42.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post22-12-2002, 13:20    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hi Bertil,

icon_lol.gif
You're absolutely right; immersion heaters aren't exactly complicated.
But the thought of forgetting to unplug something before leaving is not so far-fetched – it's even said to have happened with the fuel nozzle before.
http://hometown.aol.de/M%20Hoffmann2/Drivethr.jpg
(And NO, that sexist phrase is NOT from me!)

Okay, then it will be the immersion heater.


Translated on 23-10-2026, 17:44.
Back to top
DocSnydor
Guest




 


Free account, no CAN development support

Post23-12-2002, 9:26    Subject: TDI: How Fast to 90°C? (96 kW) Quote

I have a heater from icon_biggrin.gif Globus. It cost 24.95 DM back then (a space heater). For example, when it's -15°C, I turn it on an hour early, and the windshields are clear, and it's also warm inside. The only downside is that this thing uses 2000 watts icon_mad.gif and the engine stays cold. A submersible heater is a much better solution.


Translated on 23-10-2026, 17:45.
Back to top
Markus H.
Guest




 


Free account, no CAN development support

Post23-12-2002, 14:47    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hi,

I have a Globus radiator in my bathroom.

But what's less important to me is that *I* am cold in the car. What I want to achieve is to prevent the engine from freezing.
That's why I ordered the immersion heater from the BOSCH service today, but the Waeco model, not the Calix one.
Once I've installed it (not before January 6th), I might briefly let you know what it's 'capable of'...


Translated on 23-10-2026, 17:46.
Back to top
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post23-12-2002, 18:45    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Markus H. wrote:
...but the one from Waeco, not the Calix part...


... do you think they are different??? well, I couldn't recognize any differences icon_smile.gif.
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:47.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post24-12-2002, 0:55    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Hi Bertil,

But of course, they are different.
On one it says 'Waeco', and on the other it says 'Calix'...

No, seriously: The BOSCH service actually offered Waeco products.
And I once found a test online that claimed the Calix had a higher heating output. I don't really care.


Translated on 23-10-2026, 17:48.
Back to top
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post24-12-2002, 17:44    Subject: TDI: How Fast to 90°C? (96 kW) Quote

Markus H. wrote:
but of course, they are different:
One says "Waeco" and the other says "Calix"...

That's all there is to it. The supplier is the same!
Quote:

No, seriously: The BOSCH service just offered Waeco products.
And on the internet, I once found a test that attributed a higher heating power to the Calix.
I don't really care.
... I was once at ACDC Motorwelt, and I think their review is nonsense because the Teles are definitely the same!

It doesn't matter what you get cheaper, it will be installed anyway!
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:49.
Back to top Profile PM
Markus H.
Guest




 


Free account, no CAN development support

Post07-01-2003, 22:11    Subject: Heat Exchanger: Types, Applications & Benefits Quote

Hi Bertil,

I have now installed the Waeco immersion heater in the AAT.
This morning, I tested it for the first time, and it ran for 20 minutes.
In short: I'll probably have to run it for a significantly longer time to heat it up properly.
I'm a little concerned about the heating time.

Therefore, the question is:
Does this device have a fuse or a safety thermostat to prevent overheating?
I don't have any documentation for that part, so sorry for the silly question!


Translated on 23-10-2026, 17:50.
Back to top
Bertil
Profi-Schrauber
Profi-Schrauber


Joined: 04/15/2002
Posts: 5628
Karma: +108 / -0   Thank you, like it!


Premium Support

Post08-01-2003, 7:02    Subject: Heat Exchanger for Sale: Trade/Exchange Quote

Markus H. wrote:
Hi Bertil,

I have now installed the Waeco immersion heater in the AAT.
This morning, I tested it for the first time, and it ran for 20 minutes.
In short: I'll probably have to run it for a significantly longer time.
I'm a little concerned about the heating time.

Hi Markus,

"20 minutes is definitely not enough. With my CALIX, there was a table included that specified the minimum time, ranging from 1 hour at 5-0°C to 3 hours at -20°C. I currently preheat for 1.5 hours."
If I can find the table, I'll post it here.

Quote:


Therefore, the question is:
Does this device have a fuse or a safety thermostat to prevent overheating?
I don't have any documentation for that part, so that's why I'm asking this silly question!


I'm not entirely sure either, but in order to obtain CE certification, this component requires such an overprotection mechanism.
According to the Calix instructions, overheating is not possible as long as there is cooling water in (or around) the heating device.
Gruß Bertil

Skoda 5E5 CZDA + Mini R50 W10 + VW ID.3 + Fiat Ducato 250 + 161 DX

*** Technische Anfragen per PN werden von mir nicht beantwortet! ***


Translated on 23-10-2026, 17:53.
Back to top Profile PM
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Transmission, Chassis, Body & Interior
Go to page: 1, 2  Next
Similar articles and topics
Topic Forum
No new posts A4 Documentary: Fuel Drop After Reserve (1999) Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts really fast, completely full refueling Diesel Engine Technology
No new posts How quickly does a water heater warm up? Diesel Engine Technology
No new posts BMR to Opto Interface: Fast & Easy Setup On-Board Diagnostics (OBD)
No new posts Diesel Engine Heats Up Quickly - Troubleshooting Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.