| Author |
Message |
@udi Blaumann

Joined: 10/20/2009 Posts: 23 Karma: +1 / -0
Free account, no CAN development support
|
29-06-2011, 21:59 Subject: |
Quote |
|
Hello Herbert.
My primary concern is to help Mike.
The post has been active since May 22nd.
Mike has asked several times, but nothing has happened.
Now he has disassembled the pump.
Let's see what else needs to be done...
Best regards,
Jörg
Translated on 01-11-2026, 23:43.
|
|
| Back to top |
Profile PM |
 |
Steffen W Profi-Schrauber

Joined: 07/05/2008 Posts: 1276 Karma: +104 / -0 Location: Altenburg
Premium Support
|
30-06-2011, 6:33 Subject: |
Translating... |
|
|
Passat Variant BGW 2005
2024 Dacia Duster blue dci 115 |
|
| Back to top |
Profile PM |
 |
Dieselmike Guest
Free account, no CAN development support
|
30-06-2011, 9:08 Subject: |
Quote |
|
Thank you to everyone involved for your help.
I'm now going to bite the bullet and get a refurbished pump.
Does anyone know a way to determine the correct pump type using data from the engine control unit (ECU)?
Translated on 01-11-2026, 23:44.
|
|
| Back to top |
|
 |
@udi Blaumann

Joined: 10/20/2009 Posts: 23 Karma: +1 / -0
Free account, no CAN development support
|
30-06-2011, 12:40 Subject: |
Quote |
|
Call the number I gave you.
Best regards,
Jörg
Translated on 01-11-2026, 23:45.
|
|
| Back to top |
Profile PM |
 |
dieselschrauber Administrator


Joined: 04/12/2002 Posts: 18135 Karma: +804 / -0 Location: St.Gallen 2018 Volkswagen T6 
|
30-06-2011, 19:23 Subject: |
Quote |
|
Hello,
udi was allowed to share the link, provided that the advertising doesn't get out of control.
Best regards, Rainer.
Translated on 01-11-2026, 23:45.
|
|
| Back to top |
Profile PM WWW Garage |
 |
Dieselmike Guest
Free account, no CAN development support
|
06-07-2011, 11:09 Subject: |
Quote |
|
I just learned that it doesn't matter whether a VP44 pump is used in a manual or automatic vehicle, as this is determined by the coding of the engine control unit.
Translated on 01-11-2026, 23:45.
|
|
| Back to top |
|
 |
Tagessuppe Profi-Schrauber

Joined: 11/13/2002 Posts: 1142 Karma: +38 / -0 Location: Wien 2001 Audi A2  Premium Support
|
19-07-2011, 22:47 Subject: |
Quote |
|
To my knowledge, this cannot be reconfigured in the AKE system.
Translated on 01-11-2026, 23:45.
|
|
| Back to top |
Profile PM Garage |
 |
Dieselmike Guest
Free account, no CAN development support
|
20-07-2011, 6:01 Subject: |
Quote |
|
That's correct, even though the option is selectable. That's why I also had to buy a completely new control unit from Audi. The new pump will arrive in a few days. Then we'll see what happens.
Translated on 01-11-2026, 23:46.
|
|
| Back to top |
|
 |
Dieselmike Guest
Free account, no CAN development support
|
18-09-2011, 21:25 Subject: |
Quote |
|
Okay, so I finally installed a new fuel pump, and I have to say, it's running just as badly as before. This is ridiculous! There's an error code in the memory: 'Control difference, intake manifold pressure; control limit exceeded.' It's going into limp mode 2 at 3000 RPM. Everything is new now. What could it possibly be? I noticed that my crankshaft position sensor is installed at the 6 o'clock position, which is supposed to be around the 2 o'clock position when looking at the engine (I think), but that probably doesn't matter, right?
Translated on 01-11-2026, 23:47.
|
|
| Back to top |
|
 |
mserge Schrauber

Joined: 06/20/2005 Posts: 923 Karma: +6 / -0 Location: Luxemburg
Support
|
26-09-2011, 16:25 Subject: |
Quote |
|
Hi, I'm not exactly an expert... but what exactly did you replace, the fuel pump or the VP44?
The VP44 is not self-priming, meaning that either gravity needs to feed the diesel to it, or a pre-pump is required. Since you've installed the engine in a T3, I'm not sure where the fuel is coming from.
If the fuel pump is working correctly and the VP44 is new, then the problem is most likely due to a lack of fuel. Have you used the correct filter and connected it in the right direction? The fuel temperature is also being measured... are all of these things correct?
A4 Avant 2,5 tdi 110kw; AFB; BJ2000
4 neue Nockenwellen bei 135 tkm!!
neuer Turbo bei 200.000km
neue ESP bei 216.000km
verkauft mit 225000tkm
jetzt Renault Espace 2,0 dci 172 Initiale BJ2012
Clio 2 RS 170 PS BJ2003
Translated on 01-11-2026, 23:48.
|
|
| Back to top |
Profile PM |
 |
Dieselmike Guest
Free account, no CAN development support
|
26-09-2011, 17:06 Subject: |
Quote |
|
I have already replaced the VP44. The pump is theoretically self-priming. However, it takes a long time (1.5 meters) to bleed all the air out of the diesel line, and by then the battery is drained, which shortens the lifespan of the VP44 to just a few weeks. If the system is filled with diesel, a non-return valve that prevents diesel from flowing back before the pump is also sufficient.
Something else... The new, refurbished pump, which costs 900 euros, is leaking at the shaft. The fuel is just pouring out of it. You can tell me whatever you want, but there's definitely something wrong with this thing.
The car is now going to the Chamber of Crafts. There, a master craftsman will be studying the pile of manure.
Can someone please answer my question about the speed sensor?
Translated on 01-11-2026, 23:49.
|
|
| Back to top |
|
 |