VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Diesel technology, engine technology, vehicle diagnostics, repair & maintenance.

Need help???

 
New Topic Reply 🔗 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
Erik
Guest




 


Free account, no CAN development support

Post21-05-2003, 23:32    Subject: Need help??? Quote

So, basically, I went to the workshop. My LMM was showing very high values, and they replaced it, but it didn't fix anything.
Now, it had taken me far too long, so I took him home with me. There was a fault in the fuel tank pressure sensor.
but it was deleted, a test drive was made, and it never reappeared.
what should I do
I want to verschandeln my turbo. How do I do that, and do I need to make any adjustments afterward?
my car is also good at idling
I experience some shaking or vibrations only under full load, specifically between 1700 and 2000 RPM.
I want to start doing something about it tomorrow, please help me quickly.
I'm having a hard time.
Best regards, Erik
or what else could it be
I have a chip inside.


Translated on 03-07-2026, 15:19.
Back to top
Golfmann
Guest




 


Free account, no CAN development support

Post22-05-2003, 0:35    Subject: Need help??? Translating...

[Translating...]Hallo,

was hast du für ein Auto und was für einen Motor? Laufleistung?
Was ist das für ein Chip? Im Steuergerät oder eine Box. Vielleicht zum abschalten?

Gruß Ralf
Back to top
Erik
Guest




 


Free account, no CAN development support

Post22-05-2003, 16:05    Subject: Need help??? Translating...

[Translating...]ich habe eienen afn motor
und einen wetterauerchip
135000km
Back to top
Andy
Guest




 


Free account, no CAN development support

Post22-05-2003, 18:27    Subject: Re: Hilfe??? Quote

Hi Erik,
So, therefore, I went to the workshop, and my LMM was showing very high values, and they replaced it, but it didn't help.
Now, it had taken me far too long, so I took him home with me. There was a fault in the fuel tank pressure sensor.
but it was deleted, a test drive was made, and it never reappeared.
what should I do
High values? Are you sure? And what about that?!? icon_question.gif icon_question.gif

I want to verschandeln my turbo. How do I do this, and do I need to make any adjustments afterward?
Cleaning? With water and soap or something else? What's the purpose of that? Where would the dirt be? The only reason that comes to mind would be a stuck VTG. To find out more about this, you can search online. icon_eek.gif

My car also starts well from 2000
I experience some shaking or vibrations only under full load, specifically between 1700 and 2000 RPM.
I want to start doing something about it tomorrow, please help me quickly.
I'm having a hard time.
Best regards, Erik
or what else could it be
I have a chip inside
Try to simply describe your problem in detail. With these fragments, no one can get anything out of it.
By the way, in a post dated April 23, 2003, you state that you have a Quick-Chip installed. At that time, your damaged AFN was also malfunctioning (according to the post). Switching to a different chip tuner definitely won't solve these problems. icon_evil.gif
If you really want to understand the whole thing (as you wrote in a previous post), then discard the §%$%§/ chip and focus on the problems with VAG-COM, data logging, and careful observation. icon_exclaim.gif

Best regards, Andy


Translated on 03-07-2026, 15:19.
Back to top
New Topic Reply 🔗 🖨 Dieselschrauber - Index » Diesel Engine Technology
Similar articles and topics
Topic Forum
No new posts hilfe!!! Diesel Engine Technology
No new posts help with solenoid valve On-Board Diagnostics (OBD)
No new posts Messfahrt mit VAG-COM,...... hilfe bei AUswertung? Diesel Engine Technology
This topic is locked, you cannot edit or reply. Start of injection with VAG COM change - help Diesel Engine Technology
Jump to:  
You cannot post new topics in this forum.