Error codes and their possible causes for Teves Mark 60 (Solution)

Error codes and their possible causes for Teves Mark 60.



00003
Control unit defective.

Control unit J104 is defective.



00283
Front left speed sensor G47 or front left speed sensor G47: open circuit/short circuit to positive.

Rotor is dirty or damaged.
Wheel bearing play is excessive.
Speed sensor G47 not installed correctly.
Tachometer sensor G47 is defective.
Short circuit to ground.
Incorrect control unit version.
Wiring fault: Open circuit or short circuit to positive voltage in the wiring between speed sensor G47 and control unit J104.



00285
Front wheel speed sensor, right side, G45, or front wheel speed sensor, right side, G45, open circuit/short circuit to positive.

Rotor is dirty or damaged.
Wheel bearing play is excessive.
Speed sensor G45 not installed correctly.
Speed sensor G45 is defective.
Short circuit to ground.
Incorrect control unit version.
Wiring fault: Open circuit or short circuit to positive voltage in the wiring between speed sensor G45 and control unit J104.



00287
Rear right speed sensor G44 or rear right speed sensor G44, open circuit/short circuit to positive.

Rotor is dirty or damaged.
Wheel bearing play is excessive.
Speed sensor G44 not installed correctly.
Speed sensor G44 is defective.
Short circuit to ground.
Incorrect control unit version.
Wiring fault: Open circuit or short circuit to positive voltage in the wiring between speed sensor G44 and control unit J104.



00290
Rear left speed sensor G46 or rear left speed sensor G46: open circuit/short circuit to positive.

Rotor is dirty or damaged.
Wheel bearing play is excessive.
Speed sensor G46 not installed correctly.
Speed sensor G46 is defective.
Short circuit to ground.
Incorrect control unit version.
Wiring fault: Open circuit or short circuit to positive voltage in the wiring between speed sensor G46 and control unit J104.



00538
Reference voltage.

Short circuit to positive or ground in the wiring.
Encoder for spindle speed G202.
Accelerometer G200 (for lateral acceleration).
Donor 1 for brake pressure G201.
Donor 2 for brake pressure G214.



00668
Battery voltage at terminal 30: Signal out of range.

Interruption, short circuit to positive or ground.



00778
No communication from steering angle sensor G85, implausible signal, mechanical fault.

Interruption or loose connection in the data lines between the steering angle sensor (G85) and the control unit (J104).
Steering angle sensor - G85 - defective.
The steering angle sensor (G85) is not sending any values or is sending incorrect values.
The installation position of the steering angle sensor G85 is incorrect.
The vehicle's alignment is incorrect.
The steering wheel was removed, and subsequently, no zero calibration was performed.
Unauthorized vibrations in the steering due to wear.



00810
Brake pressure sensor 1/2: Implausible signal.

Mass connection to brake pressure sensor 1 or 2 is interrupted.
Short circuit in the signal line to sensor 1 for brake pressure (G201) or sensor 2 for brake pressure (-G214).
Sensor 1 for brake pressure (G201) or sensor 2 for brake pressure (G214) is defective.
A hydraulic brake circuit has failed.



00812
Disconnect switch for magnetic coils. Brake pressure - F84.

Interruption, short circuit to positive or ground in the wiring.
Brake booster malfunction.


00813
Brake pressure sensor 2, G214: Electrical fault in the circuit.

Short circuit to positive or ground in the wiring.
Brake pressure sensor 2, part number G214, is defective.



00814
Magnetic coil for brake pressure, N247.

Interruption, short circuit to positive.
Mass in the lines:
Brake booster malfunction.
Power amplifier in control unit J104 is defective.
ABS control unit J104 is defective.



01044
Control unit incorrectly programmed.

The control unit - J104 is programmed for a vehicle with a manual transmission. The vehicle is equipped with an automatic transmission.



01130
ABS operation, implausible signal.

Electrical disturbances caused by external interference sources (high-frequency radiation).
Interruption, short circuit to positive or ground in the wiring.
ABS control unit J104 is defective.



01276
Hydraulic pump ABS V64: Signal out of range.

Interruption, short circuit to positive or in the wiring.
Internal connection of the V64 hydraulic pump to the control unit.
Hydraulic pump V64 is defective.
ABS control unit J104 is defective.
Hydraulic pump V64 is defective.



01279
Accelerator pedal for longitudinal acceleration, model G251, electric. Circuit error.

Interruption, short circuit to positive or ground in the wiring.
The installation orientation of the G251 longitudinal acceleration sensor is incorrect.
G251 longitudinal acceleration sensor is defective.



01423
G200 lateral acceleration sensor, electric. Circuit error.

Interruption, short circuit to positive or ground in the wiring.
Lateral acceleration sensor G200 is defective.
The installation orientation of the G200 lateral acceleration sensor is incorrect.



01434
Relay for brake light suppression, ESPJ508, electrical. Circuit error.

Interruption, short circuit to positive or ground in the wiring.
Relay for brake light suppression, part number J508, is defective.



01435
Sensor 1 for brake pressure, electrical, G201. Circuit error.

Short circuit to positive or ground in the wiring.
Donor 1 for brake pressure G201 - defective.



01486
The ESP test mode has been activated; see /viewtopic.php?t=26751.



01487
ESP driving test timeout.



01542
Unlikely signal from the G202 rotation rate sensor.

Interruption, short circuit to positive or ground in the wiring.
The installation orientation of the G202 rate sensor is incorrect.
Encoder for motor G202 is defective.



65535
Control unit defective.

Control unit J104 is defective.