VCDS and OBD diagnostic device in the On-Board Diagnostics Shop
Wrenchers and tuners: diesel, petrol, OBD/VCDS. Repair, maintenance, diagnostics - help that's proven on the car.

Timing Belt Change C4 AEL: Remove Auxiliary Pulley?

 
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Author Message
kmrlange
Guest




 


Free account, no CAN development support

Post29-03-2012, 14:05    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Hello everyone,

The timing belt on my AEL engine needs to be replaced again.
You can see in my signature that I've had quite a bit of 'fun' in the past, although it was mostly due to circumstances beyond my control, as indicated by the mileage of 140,000 km.
Now I'm wondering if it's possible to replace the timing chain tensioner at the front without loosening the camshaft drive sprocket, in order to minimize the adjustment effort.
I'm thinking: The new belt has the same dimensions (length, number of teeth). It should fit perfectly. I know what's all in the workshop manual, but is it really necessary?


Best regards, Kai icon_biggrin.gif

P.S.: I just replaced the rear one because it was torn after 190,000 km. I didn't replace it in 2004 because it only had 50,000 km on it at the time. However, it had already been porous for a long time. The markings were already there, so I removed the old one and installed the new one – it works perfectly. It only took about 15 minutes, and you just need a 15mm wrench.


Translated on 30-10-2026, 21:19.
Back to top
BM
Profi-Schrauber
Profi-Schrauber
Avatar-BM

Joined: 12/07/2005
Posts: 1857
Karma: +8 / -0   Thank you, like it!
Location: Nähe Düsseldorf

Premium Support

Post29-03-2012, 18:52    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Quote:
I'm thinking: The new belt has the same dimensions (length, number of teeth). It should fit perfectly. I know what's all in the workshop manual, but is it really necessary?


What do you want to hear? That it will work or that it won't?

In 50% of the cases, it generally works if it was OK beforehand. Whether that makes sense icon_question.gif.
If the wheel needs to be disassembled for checking the bearing anyway, you might as well remove the wheel itself.

Regarding 4-cylinder PD engines (with a higher success rate), whether they are 8-valve or 16-valve, I personally prefer to initially secure the timing belt sprockets. Any adjustments or modifications are made later, only if necessary. I have also found a different method for installing the timing belt that allows for a non-destructive installation.
3B5 AJM

Wer nichts weiss, muss alles glauben.

**Technische Fragen bitte ins Forum und nicht in mein Postfach**


LG, Onkel BM


Translated on 30-10-2026, 21:21.
Back to top Profile PM
kmrlange
Guest




 


Free account, no CAN development support

Post29-03-2012, 19:34    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Hi,
The engine has only 140,000 km on it, so I don't think I need to worry about it yet. I would just like to gather some information. If, like in my case in 2003, the cylinder head gasket is going to fail anyway, then everything is clear. I'm talking about the full inspection with valve clearance measurement, etc. But now I'm in the fortunate position that everything is still fine.
Best regards, Kai.


Translated on 30-10-2026, 21:23.
Back to top
BM
Profi-Schrauber
Profi-Schrauber
Avatar-BM

Joined: 12/07/2005
Posts: 1857
Karma: +8 / -0   Thank you, like it!
Location: Nähe Düsseldorf

Premium Support

Post29-03-2012, 20:13    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Quote:
I would just like to gather some experiences
.

You already have mine. Now you can start collecting your own, or you can do it the right way from the beginning.
3B5 AJM

Wer nichts weiss, muss alles glauben.

**Technische Fragen bitte ins Forum und nicht in mein Postfach**


LG, Onkel BM


Translated on 30-10-2026, 21:23.
Back to top Profile PM
roorback
Blaumann
Blaumann


Joined: 12/22/2003
Posts: 374
Karma: +1 / -2   Thank you, like it!
Location: kärnten/österreich

Free account, no CAN development support

Post30-03-2012, 10:47    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

hey

I have the AEL in my Volvo, but I think you'll have the same problem: you won't be able to remove the cover without removing the wheel, which means you won't be able to access the water pump. At least, that's what I would have said, although I didn't hesitate to loosen the front wheel.

It's also a matter of what you want to do. I once only replaced the camshaft timing chain and wanted to leave the timing belt in place, so I made some marks and later reinstalled the crankshaft pulley according to the mark - it's a quick and dirty method, but it works icon_wink.gif.

"I now have the tool/ruler to fix the alignment precisely. However, I have to admit that in all three AEL (Air Intake System) installations I've done in the engine compartment, I've always seen the hand-drawn markings, which naturally resulted in the most chaotic settings that simply don't match up. So, it seems that the "quick and dirty" approach is apparently a common practice, not just among hobby mechanics like myself..."

Sure, here is the translation of the text from German to English:

"Hello"
volvo 850 tdi - 2.5l AEL aut. bj.96 - bald 500000km
volvo v70n 2.4 - 2.5l 5Zyl Sauger bj. 2005


Translated on 30-10-2026, 21:25.
Back to top Profile PM
kmrlange
Guest




 


Free account, no CAN development support

Post30-03-2012, 11:04    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Hi,
You're right, it's possible that the water pump can't be removed if the timing cover isn't completely detached, and that would require removing the crankshaft pulley.
Okay - last time, I also put the NW wheels back in their exact original positions by matching them to the clearly visible markings of the NW fittings on the NW wheels. The 1551 tester confirmed my approach icon_smile.gif. Thank you for your comment.
Best regards, Kai.


Translated on 30-10-2026, 21:27.
Back to top
roorback
Blaumann
Blaumann


Joined: 12/22/2003
Posts: 374
Karma: +1 / -2   Thank you, like it!
Location: kärnten/österreich

Free account, no CAN development support

Post30-03-2012, 11:09    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Okay, you won't get it 100% right with those markings, that's clear. I noticed it myself just by the fact that after replacing the timing belt, the pump was slightly misaligned and injected fuel earlier than with the old timing belt. However, the adjustment is so minimal that even tightening the timing belt is noticeable on the pump.
"However, after adjusting the pump, the engine ran significantly better than before. Next time, I will also carefully adjust and secure the camshaft again – then the basic settings will be 100% accurate again."

Okay, here's the translation:

"When you remove the left camshaft sprocket for the timing belt, make sure to align the timing mark on the right sprocket – it's difficult to do this on the camshaft itself. After installing the timing belt and before tightening the left camshaft sprocket, double-check the timing mark carefully, and then secure the sprocket."
volvo 850 tdi - 2.5l AEL aut. bj.96 - bald 500000km
volvo v70n 2.4 - 2.5l 5Zyl Sauger bj. 2005


Translated on 30-10-2026, 21:28.
Back to top Profile PM
das-weberli
Guest




 


Free account, no CAN development support

Post30-03-2012, 15:24    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

I marked the rear wheel with a silver marker at the AEL (alignment mark).
Belt changed quickly. Everything is back together.

The injection start time was 52 before the change, and 64 after the change.
I left it as it is, everything's fine.

'Take a look at the camshaft...'
This refers to the 2.5 TDI R5 engine, which can operate with a camshaft for 860,000 km or more icon_cool.gif.


Translated on 30-10-2026, 21:30.
Back to top
roorback
Blaumann
Blaumann


Joined: 12/22/2003
Posts: 374
Karma: +1 / -2   Thank you, like it!
Location: kärnten/österreich

Free account, no CAN development support

Post30-03-2012, 17:57    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

das-weberli wrote:

"Take a look at the camshaft..."
This refers to the 2.5 TDI R5 engine, which can operate with a camshaft for 860,000 km or more icon_cool.gif
.
I've also never heard of any problems like that from the Volvo side. Luckily, it's just valves and things like that that are being driven by it...
"No, it will work out."
By the way, especially among Volvo enthusiasts, but also in various other forums (like the T4 forum, etc.), this engine seems to be considered very, very durable and reliable, with no major issues. Is this the case with engines from that era, or is the AEL engine specifically one of the good ones, or even better?
volvo 850 tdi - 2.5l AEL aut. bj.96 - bald 500000km
volvo v70n 2.4 - 2.5l 5Zyl Sauger bj. 2005


Translated on 30-10-2026, 21:31.
Back to top Profile PM
kmrlange
Guest




 


Free account, no CAN development support

Post30-03-2012, 19:18    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Hi Weberli,

I marked the NW wheel with a silver Sharpie at the AEL.
Belt changed quickly. Everything put back together.

'That probably means the front wheel needs to be removed, right? I definitely want to replace the water pump at the same time.'
Best regards, Kai.


Translated on 30-10-2026, 21:32.
Back to top
das-weberli
Guest




 


Free account, no CAN development support

Post30-03-2012, 19:37    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

No, I left the rear wheel on.
'On all the LT models in the company (which use the same engine as the Audi), I always left the wheel on, and I didn't fix it or anything like that.'
Everything always had to be done quickly... and it was always perfect.
Once you've done it a few times, you'll get a good feel for it!

If you want to do the valve cover gasket replacement, you can also remove the rear wheel. Then, either mark the rear wheel or remove it completely. If you're already doing that, you might as well replace the water pump seals as well.


Translated on 30-10-2026, 21:34.
Back to top
kmrlange
Guest




 


Free account, no CAN development support

Post30-03-2012, 19:41    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

How long does the WaPu last?


Translated on 30-10-2026, 21:34.
Back to top
das-weberli
Guest




 


Free account, no CAN development support

Post30-03-2012, 19:56    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

Well, with our company's light trucks, which have mileage ranging from 250,000 to 860,000 kilometers, we've always included them.
It was only defective once. It was simply leaking.

However, it had 200,000 kilometers on the odometer.
During maintenance, something was always overlooked with the LT engines. For example, the timing belt would sometimes remain in place for 200,000-300,000 km. icon_lol.gif

I replaced everything new when my car reached 314,000 km. Better safe than sorry.
Now, the race car has been sold icon_cry.gif. It was 3 times better than the V6 TDI I have now!
(AEL @ 179 hp / V6 TDI @ 163 hp)


Translated on 30-10-2026, 21:35.
Back to top
roorback
Blaumann
Blaumann


Joined: 12/22/2003
Posts: 374
Karma: +1 / -2   Thank you, like it!
Location: kärnten/österreich

Free account, no CAN development support

Post02-04-2012, 6:55    Subject: Timing Belt Change C4 AEL: Remove Auxiliary Pulley? Quote

"So, the water pump always seems to fail on my car. I think it might be related to issues that VW/Audi had in the past. The AEL engines, which used Volvo pumps, didn't have as many problems. However, I've been using aftermarket pumps for a while now, which are much cheaper. They have some differences, like using metal components instead of cast parts. But they definitely work. I think the problems might have been related to the mounting. Volvo only uses the 18-tooth pump; the 20-tooth version was discontinued, probably because of the speed/RPM."

"@weberli: I also sometimes see values of 400 Nm and ~180 hp, but I don't use those settings very often because I notice that the engine doesn't run as well with them, and the drivetrain (specifically the dual-mass flywheel) seems to be struggling. Although the car ran for 280,000 km with a chip tune and a clutch, I eventually had to completely replace the drivetrain components. Thankfully, I now have an original engine control unit. If the AEL engine is well-tuned and properly maintained – with new injectors, a turbo, and a good ESP – it can actually perform very well with 140 hp."
volvo 850 tdi - 2.5l AEL aut. bj.96 - bald 500000km
volvo v70n 2.4 - 2.5l 5Zyl Sauger bj. 2005


Translated on 30-10-2026, 21:38.
Back to top Profile PM
New Topic Reply 🔗 ⭐ 🖨 Dieselschrauber - Index » Diesel Engine Technology
Similar articles and topics
Topic Forum
No new posts Is it possible to install a G40 engine without replacing ... Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Document Golf 1J1587, Transmission Console Mounting Not R... Faults & Documentation (Audi, VW, Seat/Cupra, Skoda)
No new posts Timing belt replacement on a 1.9L PD TDI Troubleshooting & Guides
No new posts Baseline adjustment of VP37 with drive wheel removed Diesel Engine Technology
No new posts Generator Supports: Installation & Removal Transmission, Chassis, Body & Interior
No new posts Loosen Triangle Screw on ESP Guitar Diesel Engine Technology
No new posts Remove Brake Caliper: Guide & Instructions Transmission, Chassis, Body & Interior
Jump to:  
You cannot post new topics in this forum.